【国外标准】 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
5.1 The test method is designed to relate to high-speed, supercharged diesel engine operation and, in particular, to the deposit control characteristics and antiwear properties of diesel crankcase lubricating oils.5.2 The test method is useful for the evaluation of diesel engine oil quality and crankcase oil specification acceptance. This test method, along with others, defines the minimum performance level of the API categories CF and CF-2 (detailed information about passing limits for these categories is included in Specification D4485). It is also used in MIL-PRF-2104.5.3 The results are significant only when all details of the procedure are followed. The basic engine used in this test method has a precombustion chamber (as compared to direct injection) and is most useful in predicting performance of engines similarly equipped. This factor should be considered when extrapolating test results. It has been found useful in predicting results with high sulfur fuels (that is, greater than 0.5 % by mass) and with certain preemission controlled engines. It has also been found useful when correlated with deposit control in two-stroke cycle diesel engines.1.1 This test method covers a four-stroke cycle diesel engine test procedure for evaluating engine oils for certain high-temperature performance characteristics, particularly ring sticking, ring and cylinder wear, and accumulation of piston deposits. Such oils include both single viscosity SAE grade and multiviscosity SAE grade oils used in diesel engines. It is commonly known as the 1M-PC test (PC for Pre-Chamber) and is used in several API oil categories, notably the CF and CF-2 and the military category described in MIL-PRF-2104 (see Note 1).NOTE 1: Companion test methods used to evaluate other engine oil performance characteristics for API oil categories CF and CF-2 are discussed in SAE J304. The companion tests used by the military can be found in MIL-PRF-2104.1.2 The values stated in SI units are to be regarded as standard.1.2.1 Exception—The values in parentheses are provided for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This test method is arranged as follows:TABLE OF CONTENTS 1Reference Documents 2Terminology 3Summary of Test Method 4 5Apparatus 6 Test Engine 6.1 Engine Accessories 6.2 – 6.14 Engine Oil System 6.15 Cooling System 6.16 Fuel System 6.17 Intake Air System 6.18 Exhaust System 6.19 Blowby Meter 6.20 Thermocouples 6.21 Parts 6.22 Instrumentation 6.23 Crankcase Paint 6.24Reagents and Materials 7 Fuel 7.1 Test Oil 7.2 Engine Coolant 7.3 Cleaning Materials 7.4Safety 8Preparation of Apparatus 9 Supplementary Service Information 9.1 General Engine Inspection 9.2 Intake Air System 9.3 Cooling System 9.4 Engine Cooling System Cleaning 9.5 Instrumentation Calibration Requirements 9.6 Engine Crankcase Cleaning 9.7 Additional Oil Filter 9.8 Flushing Procedure Components 9.9 Flushing Procedures 9.10 Piston Cleaning Preparation 9.11 Cylinder Head 9.12 Fuel Nozzle 9.13 Measurement 9.14Procedure 10 Engine Break-in 10.1 Pre-Test Preparations 10.2 Warm-up Procedure 10.3 Operating Conditions 10.4 Periodic Measurements 10.5 Engine Oil Level 10.6 Oil Addition Procedure 10.7 Cool-Down Procedure 10.8 Shutdowns 10.9 Fuel System 10.10 Brake Specific Oil Consumption (BSOC) Calculation 10.11Inspection 11 Preparation 11.1 Inspection 11.2 Rater Training 11.3 Referee Ratings 11.4Calibration of Test Method 12 Requirements 12.1 Reference Oils 12.2 Test Numbering 12.3 Definition of a Test 12.4 New Laboratories and New Test Stands 12.5 Frequency of Calibration Tests 12.6 Specified Test Parameters 12.10 Acceptance of Calibration Tests 12.11 Failing Reference Oil Calibration Tests 12.12 Non-Standard Tests 12.13 Severity Adjustments and Control Charting 12.14 Test Reporting 12.15 Reporting Reference Results 12.16 Analysis of Reference Oils 12.17Precision and Bias 13 Precision 13.1 Bias 13.2Keywords 14 ANNEXES Figures and Schematics Annex A1 Report Forms Annex A2 Test Fuel Information Annex A3 APPENDIXES Humidity Correction Factors Appendix X1 Report Form Examples Appendix X2 1M-PC Multiple Testing Appendix X31.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D6618-23
标准名称:
Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine
英文名称:
Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations