【国外标准】 Standard Practice for Radiographic Examination
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
4.1 This practice establishes the basic parameters for the application and control of the radiographic method. This practice is written so it can be specified on the engineering drawing, specification, or contract. It is not a detailed how-to procedure to be used by the NDT facility and, therefore, must be supplemented by a detailed procedure (see 6.1). Practices E1030/E1030M, E1032, and E1416 contain information to help develop detailed technique/procedure requirements.1.1 This practice2 covers the minimum requirements for radiographic examination for metallic and nonmetallic materials.1.2 Applicability—The criteria for the radiographic examination in this practice are applicable to all types of metallic and nonmetallic materials. When specified, it may be used for radiographic inspection of metallic or non-metallic materials, weldments, castings, and brazed materials. The requirements expressed in this practice are intended to control the quality of the radiographic images and are not intended to establish acceptance criteria for parts and materials.1.3 Basis of Application—There are areas in this practice that may require agreement between the cognizant engineering organization and the supplier, or specific direction from the cognizant engineering organization. These items should be addressed in the purchase order or the contract.1.3.1 DoD contracts.1.3.2 Personnel qualification, 5.1.1.1.3.3 Agency qualification, 5.1.2.1.3.4 Digitizing techniques, 5.4.5.1.3.5 Alternate image quality indicator (IQI) types, 5.5.3.1.3.6 Examination sequence, 6.6.1.3.7 Non-film techniques, 6.7.1.3.8 Radiographic quality levels, 6.9.1.3.9 Optical density, 6.10.1.3.10 IQI qualification exposure, 6.13.3.1.3.11 Non-requirement for IQI, 6.18.1.3.12 Examination coverage for welds, A2.2.2.1.3.13 Electron beam welds, A2.3.1.3.14 Geometric unsharpness, 6.23.1.3.15 Responsibility for examination, 6.27.1.1.3.16 Examination report, 6.27.2.1.3.17 Retention of radiographs, 6.27.8.1.3.18 Storage of radiographs, 6.27.9.1.3.19 Reproduction of radiographs, 6.27.10 and 6.27.10.1.1.3.20 Acceptable parts, 6.28.1.1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E1742/E1742M-23
标准名称:
Standard Practice for Radiographic Examination
英文名称:
Standard Practice for Radiographic Examination标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM E1740-22 Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wall Covering or Ceiling Covering Composites Using a Cone Calorimeter
- 下一篇: ASTM E1743-96 Standard Practice for Selection and Use of Portable Retroreflectomers for the Measurement of Pavement Marking Materials (Withdrawn 2003)
- 推荐标准
- 国家标准计划
- BS EN IEC 61753-082-02:2024 Fibre optic interconnecting devices and passive components. Performance standard
- BS ISO 5501-2:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 5501-3:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 5501-1:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 24138:2024 Information and documentation. International Standard Content Code (ISCC)
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30491443 DC standard
- KS D ISO 9226 금속 및 합금의 부식-대기의 부식성-부식성 평가를 위한 표준 시험편의 부식 속도 결정
- KS B 0831 비파괴검사 — 초음파탐상검사 — 표준 시험편
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme