【国外标准】 Standard Performance Specification for Knitted Upholstery Fabrics for Indoor Furniture
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
5.1 Fabrics intended for this end-use should meet all of the requirements listed in Table 1.5.2 It should be recognized that fabrics can be produced utilizing an almost infinite number of combinations of construction variables (for example, type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes.) Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1.5.2.1 Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use.5.3 The uses and significance of particular properties and test method are discussed in the appropriate sections of the specified test methods.AbstractThis performance specification covers the performance requirements for knitted upholstery fabrics as used in the manufacture of new indoor furniture for general domestic use. These requirements apply to both the wale and course directions for those factors where each fabric direction is pertinent. This performance specification is not applicable to fabrics used in contract, porch, deck, or lawn furniture; nor for woven fabrics, bonded or laminated fabrics, or surface-coated fabrics (such as vinyls and urethanes). The fabric shall be tested for its resistance to yarn slippage, dimensional change, and colorfastness to water, solvent, crocking, burnt gas fumes, light, and ozone. After the fabric has been tested, it shall be evaluated for any change in hand, character, or appearance. The fabric shall be evaluated for cracking or peeling of the back coating to check the coating durability. The fabric flammability shall also be tested. All upholstery fabrics shall be evaluated for cigarette ignition resistance.1.1 This performance specification covers the performance requirements for knitted upholstery fabrics as used in the manufacture of new indoor furniture for general domestic use. These requirements apply to both the wale and course directions for those factors where each fabric direction is pertinent.1.2 This performance specification is not applicable to fabrics used in contract, porch, deck, or lawn furniture; nor for woven fabrics, bonded or laminated fabrics, or surface-coated fabrics (such as vinyls and urethanes).1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Note 2. See 6.4.1 for a specific warning.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D4771-19
标准名称:
Standard Performance Specification for Knitted Upholstery Fabrics for Indoor Furniture
英文名称:
Standard Performance Specification for Knitted Upholstery Fabrics for Indoor Furniture标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- BS EN IEC 61753-081-02:2023 Fibre optic interconnecting devices and passive components. Performance standard