
【国外标准】 Standard Specification for Repositionable Pressure-Sensitive Flags
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers repositionable pressure-sensitive flags used to mark, flag, and index documents, books, periodicals, and so forth. Flags covered here consist of a single sheet of matte film partially covered by adhesive. A non-adhesive tab or section at one end of the flag serves for easy removal from most surfaces, including paper. The backing shall consist of polyester, polypropylene, or polyethylene film, and shall have a transparent matte surface on one side that is writable by pens and pencils. Flags are available in the following types: Type 1, which are of specified width, and have a colored tab at one end; Type 2, which are of the same width as Type 1, and have a printed message on the top side of the flag; Type 3, which twice the width of Type 1, and have a white tab at one end to highlight writing; Type 4, which are half the width of Type 1, and have a colored tab at one end; and Type 5, which are half the width of Type 1, and have an arrow or a message printed on the top side of the flag. Sampled specimens shall conform to physical requirements in terms of minimum and maximum adhesion, dispension force, and thickness.1.1 This specification covers repositionable pressure-sensitive flags used to mark, flag, and index documents, books, periodicals, and so forth.1.2 The values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently, without combining values in any way.1.3 The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D6788-02(2023)
标准名称:
Standard Specification for Repositionable Pressure-Sensitive Flags
英文名称:
Standard Specification for Repositionable Pressure-Sensitive Flags标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM A876-17e1 Standard Specification for Flat-Rolled, Grain-Oriented, Silicon-Iron, Electrical Steel, Fully Processed Types
- ASTM A877/A877M-17(2023) Standard Specification for Steel Wire, Chromium-Silicon Alloys, Chrome-Silicon-Vanadium Alloy Valve Spring Quality
- ASTM A878/A878M-19 Standard Specification for Steel Wire, Modified Chromium Vanadium Valve Spring Quality
- ASTM A882/A882M-20 Standard Specification for Filled Epoxy-Coated Seven-Wire Steel Prestressing Strand
- ASTM A886/A886M-17 Standard Specification for Steel Strand, Indented, Seven-Wire Stress-Relieved for Prestressed Concrete
- ASTM A887-20 Standard Specification for Borated Stainless Steel Plate, Sheet, and Strip for Nuclear Application
- ASTM A888-23 Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
- ASTM A890/A890M-18a Standard Specification for Castings, Iron-Chromium-Nickel-Molybdenum Corrosion-Resistant, Duplex (Austenitic/Ferritic) for General Application
- ASTM A893/A893M-03(2022) Standard Test Method for Complex Dielectric Constant of Nonmetallic Magnetic Materials at Microwave Frequencies
- ASTM A899-91(2021) Standard Specification for Steel Wire, Epoxy-Coated
- ASTM A901-19 Standard Specification for Amorphous Magnetic Core Alloys, Semi-Processed Types
- ASTM A902-23a Standard Terminology Relating to Metallic Coated Steel Products
- ASTM A903/A903M-99(2017) Standard Specification for Steel Castings, Surface Acceptance Standards, Magnetic Particle and Liquid Penetrant Inspection
- ASTM A904-20 Standard Specification for 50 Nickel-50 Iron Powder Metallurgy Soft Magnetic Parts
- ASTM A906/A906M-02(2022) Standard Specification for Grade 80 and Grade 100 Alloy Steel Chain Slings for Overhead Lifting