
【国外标准】 Standard Test Method for Tires, Pneumatic, Low Speed, Off Highway
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
4.1 This test method establishes a standard procedure of comparative testing, for tire strength and dimensional characteristics, for use under the Administrator's Cooperative Approved Tire List (CATL) (2).1.1 This test method covers measurements for comparative tire strength and dimensional characteristics. This test method covers new and retreaded pneumatic tires, both tube and tubeless types, and flaps when applicable, for mounting on construction, earthmoving, mining and logging equipment, graders, mobile cranes, and similar vehicles operated at low speeds off the road.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F1923-21
标准名称:
Standard Test Method for Tires, Pneumatic, Low Speed, Off Highway
英文名称:
Standard Test Method for Tires, Pneumatic, Low Speed, Off Highway标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- AS 1038.21.1.2-2002 (R2013) Coal and coke - Analysis and testing Higher rank coal and coke - Relative density - Analysis sample/volumetric method
- AS 1038.21.2-1992 Coal and coke - Analysis and testing Higher rank coal and coke - Relative density - Lump sample
- AS 1807.21-1989 Cleanrooms, workstations and safety cabinets - Methods of test Determination of inward air velocity of Class I biological safety cabinets
- AS 2005.21.1-1990 Low voltage fuses - Fuses with enclosed fuse-links Supplementary requirements for fuses for use by authorized persons (Fuses mainly for industrial application) - Standardized fuse systems - Fuses with fuse-links with blade contacts
- AS 2005.21.2-1990 Low voltage fuses - Fuses with enclosed fuse-links Supplementary requirements for fuses for use by authorized persons (Fuses mainly for industrial application) - Standardized fuse systems - Fuses with fuse-links for bolted connections
- ASTM D6099-18 Standard Test Method for Polyurethane Raw Materials: Determination of Acidity in Moderate to High Acidity Aromatic Isocyanates
- ASTM D610-08(2019) Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces
- ASTM D6100-17 Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM)
- ASTM D6104-97(2017)e1 Standard Practice for Determining the Performance of Oil/Water Separators Subjected to Surface Run-Off
- ASTM D6105-04(2019) Standard Practice for Application of Electrical Discharge Surface Treatment (Activation) of Plastics for Adhesive Bonding
- ASTM D6107-97(2023) Standard Specification for Stop-Leak Additive for Engine Coolants Used in Light Duty Service
- ASTM D6108-19 Standard Test Method for Compressive Properties of Plastic Lumber and Shapes
- ASTM D611-23 Standard Test Methods for Aniline Point and Mixed Aniline Point of Petroleum Products and Hydrocarbon Solvents
- ASTM D6111-19a Standard Test Method for Bulk Density And Specific Gravity of Plastic Lumber and Shapes by Displacement
- ASTM D6112-23 Standard Test Methods for Compressive and Flexural Creep and Creep-Rupture of Plastic Lumber and Shapes