【国外标准】 Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
5.1 There are three types of olefinic groups present in sufficient concentrations to warrant consideration, one or more of that can normally be found in any polyethylene. The three types are trans-vinylene, R-CH=CH-R′, sometimes referred to as trans-internal unsaturation; vinylidene or pendent methylene, RR′C-CH2; and vinyl unsaturation, R-CH=CH2, also referred to as terminal unsaturation.5.2 The type and quantity of these groups can influence the chemical and physical properties of the resin. Information concerning their presence can also be used to characterize or identify unknown resins or blends of resins.5.3 Additives can interfere with unsaturation measurements. The use is cautioned to determine which additives are present and if there any absorbance bands caused by additive presence that overlap or interfere with unsaturation absorbance bands used in this test method in the range of 1050 to 850 cm–1. If overlapping bands occur, the method is not applicable.5.4 Interference fringes resulting from smooth sample surfaces can cause measurement errors. This test method requires the use of aluminum foil in the compression molding of samples to provide an adequately rough surface to minimize interference fringes.1.1 This test method covers most types of polyethylene, those ethylene plastics consisting of ethylene and α-olefin comonomers longer than propylene, and blends of the above in any ratio.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 8.NOTE 1: There is no known ISO equivalent for this standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D6248-21
标准名称:
Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry
英文名称:
Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- BS EN IEC 61753-081-02:2023 Fibre optic interconnecting devices and passive components. Performance standard