【国外标准】 Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
This specification covers engineering and design criteria for rigid wall relocatable structures (RWRSs) which shall be used for designing expandable and nonexpendable RWRSs. RWRSs shall be manufactured from recovered materials, wherein intimate contact of dissimilar materials shall not be allowed (to prevent galvanic corrosion), all components shall be adequately protected from corrosion, and the materials used shall not cause any skin irritation or injury to the person handling the material during transportation, operation, or maintenance of the equipment. Tests for compatibility, air transportability, ground mobility, rail transportability, forklift handling, erecting and striking, air tightness, blackout, humidity resistance, marine atmosphere, temperature, solar load, temperature shock, heat transfer, blowing sand, sunshine (ultraviolet effects), flame resistance, fungus resistance, squareness, panel flatness, roof loads, floor loads, door loads, panel attachment points, leveling devices, lifting and towing provision strength, tow and dragging simulator, flat and rotational drop (with or without skids), drop shock, impact resistance, electromagnetic interference provisions, water tightness, and lift shall be performed and shall conform to the requirements specified.1.1 This specification covers engineering and design criteria required for the development of rigid wall relocatable structures (RWRS) and shall be applied to the design of expandable and nonexpandable RWRSs. This specification applies to present engineering and design requirements for effective RWRSs that are operable in a variety of environments without degradation and are capable of all specified transport modes. This specification shall be applied to the design of expandable and nonexpandable RWRSs. This specification is a conversion of a military standard that was approved by all departments and agencies of the Department of Defense.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following safety hazards caveat pertains only to the test required portion, Section 10, of this specification. This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E1925-18
标准名称:
Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures
英文名称:
Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- BS EN ISO 6224:2024 - TC . Specification
- BS ISO/IEC 15426-2:2023 conformance specification
- BS EN ISO/ASTM 52915:2020 Specification for additive manufacturing file format (AMF) Version 1.2
- 24/30474967 DC test specification - Direct Part Mark (DPM)
- BS EN ISO 6224:2024 Thermoplastics hoses, textile-reinforced, for general-purpose water applications. Specification
- BS EN ISO 4641:2024 Rubber hoses and hose assemblies for water suction and discharge. Specification
- BS EN ISO 5771:2024 - TC Tracked Changes. Rubber hoses and hose assemblies for transferring anhydrous ammonia. Specification
- PAS 4441:2024 Components used in hydrogen gas metering. Specification
- BS 5106:2024 Dimensions of spiral anti-extrusion back-up rings and their housings. Specification
- BS EN ISO 17871:2020+A1:2024 Gas cylinders. Quick-release cylinder valves. Specification and type testing
- BS EN ISO 5771:2024 Rubber hoses and hose assemblies for transferring anhydrous ammonia. Specification
- 24/30465245 DC , strength class 1 100 MPa. Procurement specification
- BS ISO/IEC 24778:2024 - TC . Aztec Code bar code symbology specification
- BS ISO/IEC 23415:2024 Information technology. Data Format Description Language (DFDL) v1.0 Specification
- BS EN ISO 10297:2024 - TC Tracked Changes. Gas cylinders. Cylinder valves. Specification and type testing