【国外标准】 Standard Test Method for Constant Torque Thermal Cycling of Cylindrical Shape Memory Alloy Specimens
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
4.1 Constant torque thermal cycling tests determine the effect of shear stress on the transformation properties such as transformation temperatures, actuation shear strain and residual shear strain of a shape memory alloy. This test is done to provide data for the characterization selection of shape memory alloy materials, quality control, design allowables and actuator design (1-3).5 The tests should be used for one thermal cycle but may be used for repeated thermal cycles as agreed upon between supplier and customer.4.2 Measurement of the specimen's motion closely parallels many shape memory actuator applications and provides a result that is applicable to the function of the material.4.3 This test method may be used for cylindrical specimens such as wire, round tube or bar forms. Thus, it is able to provide an assessment of the product in its semi-finished form.4.4 This test method provides a simple method for determining transformation temperatures by heating and cooling specimens through their full thermal transformation under torque.4.5 This test method may also be used to evaluate partial transformation cycles as set by the LCT and UCT and agreed upon between the user and customer. Examples of partial and full transformation thermal cycles are provided in Fig. 2.FIG. 2 Effects of Shear Stress and Upper Cycle Temperature on Test ResultsNOTE 1: A) UCT sufficient for complete Austenitic transformation. B) UCT not sufficient for complete Austenitic transformation. “τ” is the applied shear stress.4.6 This test method can be used on trained and processed material in a semi-finished form to measure Two Way Shape Memory Effect (TWSME) by comparing the shear strain at the LCT and UCT with a torque set such that the corresponding shear stress shall not exceed 7 MPa. For determining TWSME in this manner it is suggested that a full transformation cycle be performed in accordance with 5.7.4.7 This test method is useful for quality control, specification acceptance, and research.4.8 Transformation temperatures derived from this test method may not agree with those obtained by other test methods due to the effects of shear strain and shear stress on the transformation.4.9 Components such as springs, specimens with non-circular cross-sections or other semi-finished parts can be tested using this method as agreed upon by the customer and supplier. Test parameters and results shall be determined with respect to torque and rotation measured at the ends of the active region of the specimen.1.1 This test method will define procedures for thermomechanical cycling of shape memory alloys (SMA) material and components with circular cross-sections under constant torque. This test method will measure the transformation properties such as transformation temperatures, actuation shear strain and residual shear strain, when a shape memory alloy is thermally cycled through the phase transformation under a constant applied torque. This test is done to provide data for the characterization selection of shape memory alloy materials, quality control, design allowables and actuator design.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E3414-23
标准名称:
Standard Test Method for Constant Torque Thermal Cycling of Cylindrical Shape Memory Alloy Specimens
英文名称:
Standard Test Method for Constant Torque Thermal Cycling of Cylindrical Shape Memory Alloy Specimens标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- 24/30485462 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard