
【国外标准】 Standard Practice for Determining the Fungus-Eliminating Effectiveness of Hygienic Handwash and Handrub Agents Using the Fingerpads of Adults
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 This in vivo procedure is designed to test the ability of hygienic handwash or handrub agents to eliminate fungal contamination from experimentally-contaminated hands. Since the two thumbpads and all eight fingerpads can be used in any given test, it allows for the incorporation of an input control (two), control for culturable cells of the test fungus remaining after the inoculum has dried (two), fungal cells eliminated after treatment with a control or reference solution (two), and up to four replicates to assess the fungus-eliminating efficiency of the formulation under test. No more than 100 µL of the test fungal suspension is required to complete one test.5.2 Whereas this practice is designed to work with fungi, similar ASTM standards exist for testing against viruses (Test Method E1838) and vegetative bacteria (Test Method E2276).5.3 The levels of culturable microorganisms left on hands after washing can be reduced further by drying the washed hands with paper, cloth, or warm air (5). A step for the drying of fingerpads after exposure to the control or test solution, therefore, has not been included to avoid fungal removal by the drying process itself.5.4 This practice is not designed to test surgical hand scrubs or preoperative skin preps.5.5 The level of contamination with culturable fungi on each fingerpad after the drying of the inoculum should be at least 104 CFU so that it would permit the detection of up to a 4-log10 reduction in the viability titer of the test organism by a test formulation under the conditions of this test. This in itself does not represent the product performance criterion, which may vary depending on the jurisdiction and the nature of the formulation being evaluated.1.1 This practice is designed to assess the ability of hygienic handwash and handrub agents to reduce levels of fungal contamination on hands (3) . This practice is not meant for use with surgical hand scrubs (Test Method E1115) or preoperative skin preps (Test Method E1173).1.2 Performance of this procedure requires the knowledge of regulations pertaining to human experimentation.31.3 The practice should be performed by persons with training in microbiology in facilities designed and equipped for work with infectious agents at biosafety level 2 (4).1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E2613-23
标准名称:
Standard Practice for Determining the Fungus-Eliminating Effectiveness of Hygienic Handwash and Handrub Agents Using the Fingerpads of Adults
英文名称:
Standard Practice for Determining the Fungus-Eliminating Effectiveness of Hygienic Handwash and Handrub Agents Using the Fingerpads of Adults标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM F2044-09(2019)e1 Standard Specification for Liquid Level Indicating Equipment, Electrical
- ASTM F2046-00(2022) Standard Specification for Tachometers, Various
- ASTM F2049-11(2017) Standard Safety Performance Specification for Fences/Barriers for Public, Commercial, and Multi-Family Residential Use Outdoor Play Areas
- ASTM F2050-19 Standard Consumer Safety Specification for Hand-Held Infant Carriers
- ASTM F2051-00(2022) Standard Specification for Implantable Saline-Filled Breast Prostheses
- ASTM F2054/F2054M-13(2020) Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within Restraining Plates
- ASTM F2055-17(2021) Standard Test Method for Size and Squareness of Resilient Floor Tile by Dial Gauge Method
- ASTM F2059-21 Standard Test Method for Laboratory Oil Spill Dispersant Effectiveness Using the Swirling Flask
- ASTM F2061-17 Standard Practice for Chemical Protective Clothing: Wearing, Care, and Maintenance Instructions
- ASTM F2062-00(2018) Standard Specification for Square Drive Interconnections on Surgical Instruments
- ASTM F2064-17 Standard Guide for Characterization and Testing of Alginates as Starting Materials Intended for Use in Biomedical and Tissue Engineered Medical Product Applications
- ASTM F2075-20 Standard Specification for Engineered Wood Fiber for Use as a Playground Safety Surface Under and Around Playground Equipment
- ASTM F2076-01(2022) Standard Practice for Communicating an EMS Patient Report to Receiving Medical Facilities
- ASTM F2080-23 Standard Specification for Cold-Expansion Fittings with Metal Compression-Sleeves for Crosslinked Polyethylene (PEX) Pipe and SDR9 Polyethylene of Raised Temperature (PE-RT) Pipe
- ASTM F2082/F2082M-23 Standard Test Method for Determination of Transformation Temperature of Nickel-Titanium Shape Memory Alloys by Bend and Free Recovery