【国外标准】 Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
5.1 The performance under bending and compression load of a thermoplastic plastic pipe wall design obtained by this method can be used for the following:5.1.1 To determine the stiffness of the pipe wall section. This is a function of the pipe dimensions, the wall design, the arc length tested, and the physical properties of the material of which the pipe is made.5.1.2 To compare the characteristics of various thermoplastic pipe wall designs.5.1.3 To compare the characteristics of various plastics in pipe form.5.1.4 To study the interrelations of dimensions, materials, and deformation properties of thermoplastic pipe designs.5.1.5 To measure the deformation and load-resistance at any of several significant events which may occur during the test.5.1.6 To provide a reasonable quality control/quality assurance test for very large diameter plastic pipes.5.2 The time-dependent pipe wall stiffness of a thermoplastic pipe obtained by this test method may used for the following:5.2.1 To predict the residual stiffness of the pipe wall in bending and compression at all times after initial loading.5.2.2 For purposes of design, to determine a modulus of relaxation under sustained loads.5.2.3 To quantify the influence of material formulations of thermoplastics on the modulus of relaxation.5.2.4 To study the influence of geometric patterns of wall profiles on the modulus of relaxation.5.3 The time-independent reduction of wall thickness at springline may be used for the following:5.3.1 For pipe wall stiffness, to quantify the efficiency of all wall profiles of any material composition and a given geometry with that of a solid uniform thickness wall.1.1 This test method covers the determination of the load-deflection behavior of thermoplastic pipe wall sections under parallel plate loading conditions.NOTE 1: These are not full pipe section tests, but pipe wall segment tests. The results of these tests will be different from pipe stiffness tests per Test Method D2412, although they may be proportional. This test provides quite different information, including stress relaxation under constant strain, and comparisons of the function and stiffness of different pipe wall designs or materials.1.2 This test method covers a loading test for determining the wall stiffness of a thermoplastic-pipe wall under a combined load of bending and compression. Changes in pipe wall profile geometry under load may also be determined.1.3 This test method covers thermoplastic pipe.1.4 The characteristics determined by this test method are wall stiffness and changes in profile wall dimensions at specific deformations.1.5 The characteristics determined by this test method are wall stiffness, profile wall efficiency, and for some wall elements stability at specific Strain levels.1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F2433-05(2018)
标准名称:
Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness
英文名称:
Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM F2432-12(2018) Standard Specification for Ice Making Machines, Icemaker-Dispensers, and Ice Dispensing Equipment
- 下一篇: ASTM F2434-19 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing
- 推荐标准
- 国家标准计划
- BS ISO 24138:2024 Information and documentation. International Standard Content Code (ISCC)
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard