- 您的位置:
- 中国标准在线服务网 >>
- 全部标准分类 >>
- 国外标准 >>
- ASTM >>
- ASTM E340-23 Standard Practice for Macroetching Metals and Alloys
【国外标准】 Standard Practice for Macroetching Metals and Alloys
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
3.1 Applications of Macroetching: 3.1.1 Macroetching is used to reveal the heterogeneity of metals and alloys. Metallographic specimens and chemical analyses will provide the necessary detailed information about specific localities, but they cannot give data about variation from one place to another unless an inordinate number of specimens are taken.3.1.2 Macroetching, on the other hand, will provide information on variations in (1) structure, such as grain size, flow lines, columnar structure, dendrites, and so forth; (2) variations in chemical composition as evidenced by segregation, carbide and ferrite banding, coring, inclusions, and depth of carburization or decarburization. The information provided about variations in chemical composition is strictly qualitative but the location of extremes in segregation will be shown. Chemical analyses or other means of determining the chemical composition would have to be performed to determine the extent of variation. Macroetching will also show the presence of discontinuities and voids, such as seams, laps, porosity, flakes, bursts, extrusion rupture, cracks, and so forth.3.1.3 Other applications of macroetching in the fabrication of metals are the study of weld structure, definition of weld penetration, dilution of filler metal by base metals, entrapment of flux, porosity, and cracks in weld and heat affected zones, and so forth. It is also used in the heat-treating shop to determine location of hard or soft spots, tong marks, quenching cracks, case depth in shallow-hardening steels, case depth in carburization, effectiveness of stop-off coatings in carburization, and so forth. In the machine shop, it can be used for the determination of grinding cracks in tools and dies.3.1.4 Macroetching is used extensively for quality control in the steel industry, to determine the tone of a heat in billets with respect to inclusions, segregation, and structure. Forge shops, in addition, use macroetching to reveal flow lines in setting up the best forging practice, die design, and metal flow. For an example of the use of macroetching in the steel forging industry see Method E381. Forging shops and foundries also use macroetching to determine the presence of internal faults and surface defects. The copper industry uses macroetching for control of surface porosity in wire and bar. In the aluminum industry, macroetching is used to evaluate extrusions as well as the other products such as forgings, sheets, and so forth. Defects such as coring, cracks, and porthole die welds are identified.1.1 These procedures describe the methods of macroetching metals and alloys to reveal their macrostructure.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to the International System (SI) units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.For specific warning statements, see 6.2, 7.1, 8.1.3, 8.2.1, 8.8.3, 8.10.1.1, and 8.13.2. It is further recommended to review the guidance in Guide E2014.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E340-23
标准名称:
Standard Practice for Macroetching Metals and Alloys
英文名称:
Standard Practice for Macroetching Metals and Alloys标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- BS EN IEC 61753-082-02:2024 Fibre optic interconnecting devices and passive components. Performance standard
- BS ISO 5501-2:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 5501-3:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 5501-1:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 24138:2024 Information and documentation. International Standard Content Code (ISCC)
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30491443 DC standard
- KS D ISO 9226 금속 및 합금의 부식-대기의 부식성-부식성 평가를 위한 표준 시험편의 부식 속도 결정
- KS B 0831 비파괴검사 — 초음파탐상검사 — 표준 시험편
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication