
【国外标准】 Standard Practice for Sampling Zooplankton with Conical Tow Nets
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
3.1 The advantages of using conical tow nets are as follows:3.1.1 They are relatively inexpensive and highly versatile in a variety of inland, estuarine, coastal, and marine waters.3.1.2 They can be used from a small or large powered boat with a minimum of auxiliary equipment.3.1.3 They can be used to collect qualitative samples and semiquantitative samples when fitted with a flowmeter and even better samples when fitted with a companion meter on the outside of the hoop to monitor filtering efficiency.3.2 The disadvantages of conical tow nets are as follows:3.2.1 When equipped with a flowmeter they require frequent maintenance including calibration and, in some types, lubrication.3.2.2 They are effective only where drawn through a stream of water having considerable thickness. They are not suitable for collecting samples from a small or restricted region.3.2.3 They are not suitable for collecting in very shallow water.3.2.4 They are clogged by grass beds, coelenterates, and filamentous algae.3.2.5 When used with a flowmeter, they collect only qualitative samples, or semiquantitative samples.3.2.6 When sampling discrete depths using a horizontal tow, the sample can be contaminated from other depths during the deployment and retrieval of the samples if opening and closing devices are not used.3.3 There are several special considerations that shall be observed when using conical tow nets. They are:3.3.1 Conical tow net samplers are designed to be towed at speeds less than three knots; however, greater speeds have been used for the larger nets with a concomitant increase in capture.23.3.2 A conical tow net 0.5 m in diameter or larger shall be used to reduce avoidance by organisms.23.3.3 The nets shall be washed frequently and inspected for pin-size holes, tears, net deterioration, and other anomalies.3.3.4 Nets should be allowed to dry while suspended full length in air and in subdued light prior to storage.3.3.5 Lower catches per sample may result when collections are made during the day. These are particularly noted in the larger zooplanktons.(A) Sage, L. E., “Zooplankton,” In Methods for the Assessment and Prediction of Mineral Mining Impacts on Aquatic Communities: A Review and Analysis, Fish Wildlife Service/Office of Biological Services, Vol 78, No. 30, April 1978, pp. 55–65.1.1 This practice covers the procedure for obtaining qualitative samples of a zooplankton community by use of conical tow nets. Nets will collect most zooplankton, but some forms will avoid nets.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E1201-19
标准名称:
Standard Practice for Sampling Zooplankton with Conical Tow Nets
英文名称:
Standard Practice for Sampling Zooplankton with Conical Tow Nets标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM E866-23 Standard Specification for Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels
- ASTM E867-23 Standard Terminology Relating to Vehicle-Pavement Systems
- ASTM E870-82(2019) Standard Test Methods for Analysis of Wood Fuels
- ASTM E871-82(2019) Standard Test Method for Moisture Analysis of Particulate Wood Fuels
- ASTM E872-82(2019) Standard Test Method for Volatile Matter in the Analysis of Particulate Wood Fuels
- ASTM E874-19 Standard Practice for Adhesive Bonding of Aluminum Facings to Nonmetallic Honeycomb Core for Shelter Panels
- ASTM E875-20 Standard Practice for Evaluation of Fungal Control Agents as Preservatives for Aqueous-Based Products Used in the Paper Industry
- ASTM E877-21 Standard Practice for Sampling and Sample Preparation of Iron Ores and Related Materials for Determination of Chemical Composition and Physical Properties
- ASTM E878-20 Standard Test Method for Determination of Titanium in Iron Ores and Related Materials by Diantipyrylmethane Ultraviolet Spectrophotometry
- ASTM E879-20 Standard Specification for Thermistor Sensors for General Purpose and Laboratory Temperature Measurements
- ASTM E88-11(2017) Standard Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition
- ASTM E882-10(2016)e1 Standard Guide for Accountability and Quality Control in the Chemical Analysis Laboratory
- ASTM E887-21 Standard Test Method for Silica in Refuse-Derived Fuel (RDF) and RDF Ash
- ASTM E889-82(2023) Standard Test Method for Composition or Purity of a Solid Waste Materials Stream
- ASTM E90-23 Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements