【国外标准】 Standard Practice for Preparing Prints of Paste Printing Inks with a Printing Gage
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
4.1 Laboratory proofing of inks is necessary to establish a reproducible prediction of print appearance and performance properties, most of which are highly sensitive to ink film thickness. The apparatus described in this practice has found wide use for routine control proofing because it provides an economical method for producing reasonably large prints at film thicknesses comparable to those obtained on production presses.FIG. 1 Schematic Diagram of Printing Gages (not drawn to scale)4.2 A unique advantage of printing gages is that, depending on the design selected, prints can be produced at a range of tapered film thicknesses or at several levels of uniform thicknesses in a single proofing. Because of the built-in film thickness control, ink metering is not necessary. Relatively small quantities of test samples are used, and less than two minutes are required to ink a gage, pull a letterpress print, and clean up. In addition, problems due to ink distribution systems are eliminated, two inks may be proofed at the same time, and multi-color printing is possible.4.3 This practice does not duplicate the dynamics of a high speed press, nevertheless, it is useful for quality control and for specification acceptance between the producer and the user.1.1 This practice covers the procedure for preparing laboratory prints of paste inks using a printing gage in conjunction with a flat-bed proof press.1.2 This practice is applicable to the preparation of solid-area prints by direct letterpress or by dry offset on a flat substrate such as paper, paperboard, or metal.1.3 This practice is applicable primarily to lithographic and letterpress inks that dry by oxidation or penetration. With the addition of appropriate drying or curing equipment, it is also applicable to other paste ink systems such as heat-set or energy-curable.1.4 The instructions in this practice are intended to minimize the within-print and among-operator variability inherent in hand operations.1.5 This practice features built-in ink film thickness control. It does not measure the film thickness transferred to the print; however, film thickness equivalence may be evaluated by visual or instrumental comparisons of optical density.1.6 Values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautions are given in Section 7.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D6846-02(2020)
标准名称:
Standard Practice for Preparing Prints of Paste Printing Inks with a Printing Gage
英文名称:
Standard Practice for Preparing Prints of Paste Printing Inks with a Printing Gage标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- BS EN IEC 61753-081-02:2023 Fibre optic interconnecting devices and passive components. Performance standard