【国外标准】 Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
AbstractThese test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for determining the following properties: product hardness; proof load by length measurement (Method 1), yield strength (Method 2), yield strength of austenitic stainless steel and nonferrous materials (Method 2A), and uniform hardness (Method 3); axial tension of full size products such as fasteners and studs; wedge tension of full size products such as fasteners and studs; tension of machined test specimens including yield point (by drop of the beam or halt of the pointer, autographic diagram, and total extension under load methods), yield strength (by offset, and extension under load methods), tensile strength, elongation, and reduction of area; and total extension at fracture. As for internally threaded fasteners including nonheat- and heat-treated nuts, tests are provided for the determination of product hardness, proof load, and cone proof load. Test for determining the surface and core hardnesses are, conversely, described for direct tension indicators, and through-hardened, carburized, stainless steel, and nonferrous washers. And finally, product hardness testing is described for rivets. The test method for determining embrittlement of metallic coated externally threaded fasteners is detailed as well.1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension indicators, and rivets.1.2 Property requirements and the applicable tests for their determination are specified in individual product standards. In those instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall specify the controlling testing requirements. In the absence of any specified test requirement(s), these test methods shall apply.1.3 These test methods describe mechanical tests for determining the following properties: SectionFor Externally Threaded Fasteners: 3 Product Hardness 3.1 Proof Load 3.2.1 Method 1, Length Measurement 3.2.3 Method 2, Yield Strength 3.2.4 Method 3, Uniform Hardness 3.2.5 Axial Tension Testing of Full-Size Product 3.4 Wedge Tension Testing of Full-Size Product 3.5 Tension Testing of Machined Test Specimens 3.6 Total Extension at Fracture Test Single Sheer Test 3.73.8For Internally Threaded Fasteners: 4 Product Hardness 4.1 Proof Load Test 4.2 Cone Proof Load Test 4.3For Washers and Direct Tension Indicators: 5 Product Hardness-General Requirements 5.1 Through Hardened Washers 5.2 Carburized Washers 5.3 Stainless Steel and Nonferrous Washers 5.4 Direct Tension Indicators 5.5 Compression Load 5.6For Rivets: 6 Product Hardness 6.1Test for Embrittlement of Metallic-Coated Externally Threaded Fasteners 7Test Method for Determining Decarburization and Carburization 81.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.NOTE 1: The values are stated in inch-pound for inch fasteners and SI metric units for metric fasteners.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F606/F606M-21
标准名称:
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
英文名称:
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- BS EN IEC 61753-081-02:2023 Fibre optic interconnecting devices and passive components. Performance standard