【国外标准】 Standard Practice for Surface Preparation and Marking of Metallic Surgical Implants
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
3.1 The objective of surface treatments as documented in this practice is to improve the corrosion resistance of metallic surgical implants including, but not limited to, those manufactured from iron, cobalt, nickel, titanium, and tantalum base materials.3.2 Iron particles, ceramic media, and other foreign particles may become smeared over or embedded into the surface of implants during processing operations such as forming, machining, tumbling, media blasting, marking, and so forth. These particles should be removed to minimize localized corrosion and superficial blemishes.3.3 The various chemical and electrochemical surface treatments specified by this practice are used to remove objectionable surface contaminants and to restore maximum corrosion resistance to, or promote the creation of, an inert or passive surface, such as a metal oxide film, as is applicable to the specific material. Some of these treatments are referred to as passivation treatments. The preferred surface treatment for a given application varies depending on the implant material and the nature of the surface contaminants.3.4 Depending on the implant, its material, and the type of marking method and procedure, the marking may be applied before or after a chemical or electrochemical surface treatment. When marking is performed after the surface treatment, the localized implant surface shall be evaluated to determine if there is a need for additional surface treatment.NOTE 1: The need for additional surface treatment is likely for stainless steel with all marking methods, and for nonferrous alloys when the marking method involves direct or second-hand contact with iron-based or other material that would be considered an objectionable surface contaminant.3.5 The selection of procedures to be applied to the implants, and additional requirements which are not covered by this practice, may be included in the implant production specification.1.1 This practice provides descriptions of surface characteristics, surface preparation, and marking for metallic surgical implants, with the purpose of improving the corrosion resistance of the implant surfaces and markings.1.2 Marking nomenclature and neutralization of endotoxin are not specified in this practice (see X1.4).1.3 Surface requirements and marking methods included in the implant specification shall take precedence over requirements listed in this practice, where appropriate.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F86-21
标准名称:
Standard Practice for Surface Preparation and Marking of Metallic Surgical Implants
英文名称:
Standard Practice for Surface Preparation and Marking of Metallic Surgical Implants标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- 24/30485462 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard