【国外标准】 Standard Classification for Determination of High-frequency Impact Sound Ratings
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
4.1 This classification provides a family of single-number ratings for describing high-frequency impact sound insulation. “High-frequency” in this context refers to the third-octave bands from 400 to 3150 Hz, which is approximately the upper half of the frequency range of interest in building acoustics measurements. Common sources of high-frequency impact sound include the impact of hard-heeled shoes, dragging furniture, dog toenails, and dropping objects on hard-surfaced flooring.4.2 The high-frequency impact sound insulation of an assembly is primarily determined by the characteristics of the floor topping, largely independent of the other details of the assembly.3 For many assemblies, the existing ratings (such as IIC) become controlled by frequency bands below 400 Hz. For these assemblies, the existing ratings are not representative of the impact insulation at high frequencies. The high-frequency ratings defined here have been shown to accurately represent the behavior of assemblies at high frequencies.4,5 These ratings are intended to aid the acoustical professional in evaluating the high-frequency insulation of an assembly, and in evaluating, rank-ordering, and specifying floor topping products that will affect the level of high-frequency impact sound.4.3 The ratings in this classification have similar numerical range and behavior as the existing ratings of Classification E989. Further, the ratings in this classification can be calculated from existing test reports without additional testing. This was done to take advantage of the existing test results and body of knowledge.4.4 This classification describes only the high-frequency range of impact sound and no other aspects of impact noise. It does not address impact sound below 400 Hz, such as thudding from footfalls, and additional ratings are required to describe impact sound in these frequency ranges. This classification does not replace Classification E989 (Impact Insulation Class) and is not interchangeable with it. For example, the HIIC rating of an assembly does not determine its IIC rating and cannot be used to show compliance with an IIC requirement. The expectation is that the high-frequency ratings would be reported alongside the existing ratings.4.5 The family of ratings described use the same calculation method and differ only in the origin of the third-octave data used in the calculation. There is a high-frequency version of each existing impact rating, in which this classification is used instead of Classification E989 to calculate the single-number rating.1.1 This classification provides methods for calculating single-number ratings of high-frequency impact sound transmission, based on one-third-octave-band impact sound pressure levels generated by the standard tapping machine as described in Test Methods E492, E1007, and E2179.1.2 This classification defines ratings that are not defined in other standards. Within their purview, other standards shall define additional ratings based on the methods of this classification.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E3222-20a
标准名称:
Standard Classification for Determination of High-frequency Impact Sound Ratings
英文名称:
Standard Classification for Determination of High-frequency Impact Sound Ratings标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM E322-12 Standard Test Method for Analysis of Low-Alloy Steels and Cast Irons by Wavelength Dispersive X-Ray Fluorescence Spectrometry (Withdrawn 2021)
- 下一篇: ASTM E3223/E3223M-20 Standard Guide for Specifying and Testing Field-Constructed Exterior Building Wall System Mockups in New Construction
- 推荐标准
- 国家标准计划
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations