【国外标准】 Standard Specification for Composite Corrugated Steel Pipe for Sewers and Drains (Withdrawn 2015)
本网站 发布时间:
2024-02-28
- ASTM A1042/A1042M-04(2009)
- Withdrawn, No replacement
- 定价: 0元 / 折扣价: 0 元
- 在线阅读
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
This specification covers composite corrugated steel pipe, intended for uses such as storm water drainage, sanitary sewers, underdrains, construction of culverts, and similar uses. The composite material used in fabrication of the pipe consists of a three-layer polymer protective coating on both sides of a steel sheet core. The composite corrugated steel pipe covered by this specification is classified as Type IC and Type ICS. Type IC pipe shall be fabricated with helical corrugations and a continuous lock seam extending helically from end to end of each length of pipe. Type ICS shall be fabricated with helical corrugations and a continuous helical lock seam extending from end to end of each length of pipe, and with a smooth high-density polyethylene liner thermally bonded to the pipe polymer coating at each interior corrugation crest over the length of the pipe. Types IC and ICS pipe shall conform to the pipe dimensions and sheet thickness. Field joints for each type of composite corrugated steel pipe shall maintain pipe alignment during construction and prevent infiltration of fill material during the life of the installation. The following types of coupling systems shall be permitted: flange type; bell and spigot type; band type with annular corrugations; flat band type; and smooth sleeve type. Specimens cut from production pipe normal to and across the lock seam shall develop the specified tensile strength.1.1 This specification covers composite corrugated steel pipe, intended for uses such as storm water drainage, sanitary sewers, underdrains, construction of culverts, and similar uses. The composite material used in fabrication of the pipe consists of a three-layer polymer protective coating on both sides of a steel sheet core. The three layers consist of an inner layer of fusion-bonded epoxy on the steel surface, an intermediate layer of polyethylene adhesive, and an outer layer of high-density polyethylene.1.2 The three-layer polymer coating protects the base metal against corrosion or abrasion, or both. Severe environments are likely to cause corrosion problems to accessory items such as coupling band hardware unless supplemental protection is provided. Additional protection for composite steel pipe is available by use of coatings applied after fabrication of the pipe as described in Specification A849.1.3 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and sheet thickness of the pipe. Experience with drainage products has shown that successful performance depends upon the proper selection of corrugation profile, sheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in installation. The installation procedure is described in Practice A798/A798M.1.4 This specification is applicable to orders in either inch-pound units as A1042, or in SI units as A1042M. Inch-pound units and SI units are not necessarily equivalent. SI units are shown in brackets in the text for clarity, but they are the applicable values when the material is ordered to A1042M.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
标准号:
ASTM A1042/A1042M-04(2009)
标准名称:
Standard Specification for Composite Corrugated Steel Pipe for Sewers and Drains (Withdrawn 2015)
英文名称:
Standard Specification for Composite Corrugated Steel Pipe for Sewers and Drains (Withdrawn 2015)标准状态:
Withdrawn, No replacement-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM A1041/A1041M-04(2009) Standard Specification for Pressure Vessel Plates, Alloy Steel, Higher Strength Chromium-Molybdenum-Tungsten (Withdrawn 2013)
- 下一篇: ASTM A1048/A1048M-06(2011) Standard Specification for Pressure Vessel Forgings, Alloy Steel, Higher Strength Chromium-Molybdenum-Tungsten for Elevated Temperature Service (Withdrawn 2016)
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- BS EN IEC 61753-081-02:2023 Fibre optic interconnecting devices and passive components. Performance standard