
【国外标准】 Standard Specification for High-Flash Aromatic Naphthas
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers two types of aromatic hydrocarbon solvents, commonly referred to as high flash aromatic naphthas, namely: Type I (Aromatic 100) and Type II (Aromatic 150). These solvents are normally petroleum distillates having moderately low volatility and are used primarily by the coatings industry. The physical and chemical properties of high-flash aromatic naphthas shall conform to the requirements specified for the following: (1) appearance, (2) color, (3) amount of aromatics, (4) copper corrosion, (5) distillation range defined by the initial boiling point and dry point, (6) flash point, (7) Kauri-butanol value, (8) mixed aniline point, (9) odor, and (10) apparent specific gravity. The sampling and test methods to determine conformance to the specified properties are given.1.1 This specification covers two types of aromatic hydrocarbon solvents, normally petroleum distillates, having high flash points, moderately low volatility, and a distillation range of approximately 30°C (50°F). These solvents are used primarily by the coatings industry and are commonly referred to as high-flash aromatic naphthas.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.1.4 For specific hazard information and guidance, see the supplier’s Safety Data Sheet for materials listed in this specification.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D3734-05(2018)
标准名称:
Standard Specification for High-Flash Aromatic Naphthas
英文名称:
Standard Specification for High-Flash Aromatic Naphthas标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D6047-17(2021) Standard Test Methods for Rubber, Raw—Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers
- ASTM D6049-03(2022) Standard Test Method for Rubber Property—Measurement of the Viscous and Elastic Behavior of Unvulcanized Raw Rubbers and Rubber Compounds by Compression Between Parallel Plates
- ASTM D6055-96(2019) Standard Test Methods for Mechanical Handling of Unitized Loads and Large Shipping Cases and Crates
- ASTM D6058-96(2016) Standard Practice for Determining Concentration of Airborne Single-Crystal Ceramic Whiskers in the Workplace Environment
- ASTM D6062-19 Standard Guide for Personal Samplers of Health-Related Aerosol Fractions
- ASTM D6063-11(2018) Standard Guide for Sampling of Drums and Similar Containers by Field Personnel
- ASTM D6064-11(2022) Standard Specification for HFC-227ea, 1,1,1,2,3,3,3-Heptafluoropropane (CF3CHFCF3)
- ASTM D6067/D6067M-17 Standard Practice for Using the Electronic Piezocone Penetrometer Tests for Environmental Site Characterization and Estimation of Hydraulic Conductivity
- ASTM D6068-10(2018) Standard Test Method for Determining J-R Curves of Plastic Materials
- ASTM D607-82(2019) Standard Specification for Wet Ground Mica Pigments
- ASTM D6071-14(2022) Standard Test Method for Low Level Sodium in High Purity Water by Graphite Furnace Atomic Absorption Spectroscopy
- ASTM D6073-08a(2020) Standard Test Method for Relative Setting of Heatset Printing Inks
- ASTM D6074-15(2022) Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils
- ASTM D6076-18(2023) Standard Test Method for Shrinkage Temperature of Leather
- ASTM D6077-16(2023) Standard Test Method for Trapezoid Tearing Strength of Leather