【国外标准】 Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
This specification covers a general requirements for specialized carbon and alloy steel pipe. Tensile tests, tension tests, flattening tests, hydrostatic tests and ultrasonic tests shall be made to conform to the requirements specified. If the mechanical results do not conform to the requirements specified, retests shall be made. Defects in seamless pipe shall be repaired by welding.1.1 This specification2 covers a group of requirements which, with the exceptions of Section 6.3, Section 14, Section 21, and Section 22, are mandatory requirements to the ASTM pipe product specifications noted below unless the product specification specifies different requirements, in which case the requirement of the product specification shall prevail.1.2 Sections 6.3 or 21 are mandatory if the product specification has a requirement for product analysis or flattening tests.1.3 Section 22 is mandatory if the product specification has a hydrostatic test requirement without defining the test parameters.1.4 Section 14 is for information only.1.5 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification, only the requirement of the product specification need be satisfied.Title of Specification ASTM DesignationASeamless Carbon Steel Pipe for High-Temperature Service A106/A106MMetal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission Systems A381Seamless Carbon Steel Pipe for Atmospheric and Lower Temperatures A524Centrifugally Cast Carbon Steel Pipe for High-Temperature Service A660/A660MElectric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures A671/A671MElectric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures A672/A672MCarbon and Alloy Steel Pipe, Electric-Fusion-Welded for High-Pressure Service at High Temperatures A691/A691M1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.NOTE 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM A530/A530M-18
标准名称:
Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
英文名称:
Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations