购物车
400-168-0010
【国外标准】 Geographic information - Imagery sensor models for geopositioning - Part 2: SAR, InSAR, lidar and sonar
标准简介适用范围：
ISO/TS 19130-2:2014 supports exploitation of remotely sensed images. It specifies the sensor models and metadata for geopositioning images remotely sensed by Synthetic Aperture Radar (SAR), Interferometric Synthetic Aperture Radar (InSAR), LIght Detection And Ranging (lidar), and SOund Navigation And Ranging (sonar) sensors. The specification also defines the metadata needed for the aerial triangulation of airborne and spaceborne images.
ISO/TS 19130-2:2014 specifies the detailed information that shall be provided for a sensor description of SAR, InSAR, lidar, and sonar sensors with the associated physical and geometric information necessary to rigorously construct a physical sensor model. For the case where precise geoposition information is needed, this Technical Specification identifies the mathematical formulae for rigorously constructing physical sensor models that relate two-dimensional image space to three-dimensional ground space and the calculation of the associated propagated error.
ISO/TS 19130-2:2014 does not specify either how users derive geoposition data or the format or content of the data the users generate.
标准号：
ANSI/INCITS/ISO TS 19130-2:2014[2015]
标准名称：
Geographic information - Imagery sensor models for geopositioning - Part 2: SAR, InSAR, lidar and sonar
英文名称：
Geographic information - Imagery sensor models for geopositioning - Part 2: SAR, InSAR, lidar and sonar标准状态：
现行-
发布日期：
-
实施日期：
出版语种：
- 其它标准
- 上一篇： ANSI/IAS U.S. LC 2-1996 Direct Gas-Fired Circulating Heaters for Agricultural Animal Confinement Buildings
- 下一篇： ANSI/INCITS/ISO/IEC 18092:2013[2015] Information technology -- Telecommunications and information exchange between systems -- Near Field Communication -- Interface and Protocol (NFCIP-1)
- 推荐标准
- ASTM E716-16(2021)e2 Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry
- ASTM F1035-03(2015) Standard Practice for Use of Rubber-Cord Pie Disk to Demonstrate the Discernment Capability of a Tire X-ray Imaging System
- ASTM F2255-05(2015) Standard Test Method for Strength Properties of Tissue Adhesives in Lap-Shear by Tension Loading
- ASTM F2258-05(2015) Standard Test Method for Strength Properties of Tissue Adhesives in Tension
- ASTM F2392-04(2015) Standard Test Method for Burst Strength of Surgical Sealants
- ASTM F2620-20ae2 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
- ASTM F2819-10(2015)e2 Standard Test Methods for Measurement of Straightness of Bar, Rod, Tubing and Wire to be used for Medical Devices
- ASTM F665-09(2015) Standard Classification for Vinyl Chloride Plastics Used in Biomedical Application
- ASTM F754-08(2015) Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders
- ASTM G110-92(2022)e2 Standard Practice for Evaluating Intergranular Corrosion Resistance of Heat Treatable Aluminum Alloys by Immersion in Sodium Chloride + Hydrogen Peroxide Solution
- ASTM ISO/ASTM51310-22 Standard Practice for Use of a Radiochromic Optical Waveguide Dosimetry System
- ASTM ISO/ASTM51539-23 Standard Guidance for Use of Radiation-Sensitive Indicators
- ASTM ISO/ASTM51607-13 Standard Practice for Use of the Alanine-EPR Dosimetry System
- ASTM ISO/ASTM51608-15(2022) Standard Practice for Dosimetry in an X-Ray (Bremsstrahlung) Facility for Radiation Processing at Energies between 50 keV and 7.5 MeV
- ASTM ISO/ASTM51631-20 Standard Practice for Use of Calorimetric Dosimetry Systems for Dose Measurements and Routine Dosimetry System Calibration in Electron Beams
