
【国外标准】 Standard Specification for Vegetable Peeling Machines, Electric
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers batch-type electric vegetable peeling machines of the following style: Style 1, Size A, and Style 2, Size A, Size B, and Size C. The cylinder or hopper shall be sheet aluminum or stainless steel, or cast iron. Machines intended for marine applications shall be furnished with a stainless steel cylinder. The inside surface of all cylinders shall be covered by silicon carbide or aluminum oxide. The disk shall be cast aluminum, formed stainless steel, or reinforced plastic. The cylinder covering ring shall be cast aluminum, spun sheet aluminum, or fiberglass-reinforced plastic. The supporting base of the flour mounted Style 2 machine shall be steel, aluminum, or stainless steel. The vegetable peeler shall comply to the specified physical requirements specified for the following: (1) cylinder or hopper, (2) disk, (3) vegetable outlet, (4) peel trap, (5) waste outlet, (6) water inlet and sprayer, (7) cylinder covering ring, (8) Style 1, counter mounted, (9) Style 2, floor mounted, (10) waste disposer, (11) electrical devices such as motors, wiring, timer, and switch, and (12) piping, tubing, fittings, and valves. The peeler shall meet the hazard protection requirements including switch guard and shall conform to the performance requirements which shall be tested by operational test.1.1 This specification covers batch-type vegetable peeling machines.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F1371-13(2018)e1
标准名称:
Standard Specification for Vegetable Peeling Machines, Electric
英文名称:
Standard Specification for Vegetable Peeling Machines, Electric标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM 51401-21 Standard Practice for Use of a Dichromate Dosimetry System
- ASTM 51956-21 Standard Practice for Use of a Thermoluminescence-Dosimetry System (TLD System) for Radiation Processing
- ASTM A1010/A1010M-24 Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip
- ASTM A1016/A1016M-24 Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes
- ASTM A105/A105M-24 Standard Specification for Carbon Steel Forgings for Piping Applications
- ASTM A1064/A1064M-24 Standard Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete
- ASTM A108-24 Standard Specification for Steel Bar, Carbon and Alloy, Cold-Finished
- ASTM A1080/A1080M-24 Standard Practice for Hot Isostatic Pressing of Steel, Stainless Steel, and Related Alloy Castings
- ASTM A1090/A1090M-19(2024) Standard Specification for Forged Rings and Hollows for Use as Base Plates in Power Transmission Structures
- ASTM A1115/A1115M-24 Standard Practice for Construction of Mechanically Stabilized Earth Walls with Inextensible Soil Reinforcement
- ASTM A1128-24 Standard Specification for Stainless Steel Shielded, Rubber Gasketed Couplings Having an Integral Restraint Feature for Joining Hubless Cast Iron Soil Pipes and Fittings Where External Restraint Is Required
- ASTM A179/A179M-24 Standard Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes
- ASTM A234/A234M-24 Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service
- ASTM A242/A242M-24 Standard Specification for High-Strength Low-Alloy Structural Steel
- ASTM A249/A249M-24a Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes