
【国外标准】 Standard Specification for Tin Mill Products, Black Plate, Single-Reduced
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications. The black plates shall be produced with ground roll and shot-blasted roll finishes and shall be furnished oiled or dry.1.1 This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications.1.2 It may be supplied dry or oiled and with or without surface treatment. This product is normally supplied with a trimmed edge.1.3 This specification is applicable to orders in either inch-pound units (as A625), which is supplied in thicknesses from 135-lb base weight (0.0149 in.) and lighter, or SI units (as A625M), which is supplied in thicknesses from 0.378 mm and lighter.1.4 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM A625/A625M-13(2018)
标准名称:
Standard Specification for Tin Mill Products, Black Plate, Single-Reduced
英文名称:
Standard Specification for Tin Mill Products, Black Plate, Single-Reduced标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D4976-12a(2020) Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
- ASTM D4977/D4977M-20 Standard Test Method for Granule Adhesion to Mineral-Surfaced Roofing by Abrasion
- ASTM D4981-19 Standard Practice for Screening of Oxidizers in Waste
- ASTM D4982-20 Standard Test Methods for Flammability Potential Screening Analysis of Waste
- ASTM D4986-22 Standard Test Method for Horizontal Burning Characteristics of Cellular Polymeric Materials
- ASTM D4991-07(2023) Standard Test Method for Leakage Testing of Empty Rigid Containers by Vacuum Method
- ASTM D4992-22 Standard Practice for Evaluation of Rock to be Used for Erosion Control
- ASTM D4994-19 Standard Practice for Recovery of Viruses from Wastewater Sludges
- ASTM D4995-10(2020) Standard Specification for Electronic and Degreasing Grades of 1,1,2–Trichloro 1,2,2,–Trifluoroethane Solvent
- ASTM D5/D5M-20 Standard Test Method for Penetration of Bituminous Materials
- ASTM D50-90(2023) Standard Test Methods for Chemical Analysis of Yellow, Orange, Red, and Brown Pigments Containing Iron and Manganese
- ASTM D500-95(2023) Standard Test Methods of Chemical Analysis of Sulfonated and Sulfated Oils
- ASTM D5007-99(2017) Standard Test Method for Wet-to-Dry Hiding Change
- ASTM D5008-22 Standard Test Method for Ethyl Methyl Pentanol Content and Purity Value of 2-Ethylhexanol By Gas Chromatography
- ASTM D5012-20 Standard Practice for Preparation of Materials Used for the Collection and Preservation of Atmospheric Wet Deposition