
【国外标准】 Standard Specification for FEP-Fluorocarbon Tube
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers the tubing that is intended for electrical, mechanical, chemical and medical applications manufactured from extrusion resins made from the copolymer of tetrafluoroethylene and hexafluoropropylene. Three types of FEP-fluorocarbon tubing are classified which are differentiated by size schedules: Type I which is tubing based upon the American wire gage, Type II which is tubing based upon fractional inch sizes, and Type III which is tubing of all other sizes. Tubings are further differentiated in accordance to its increasing wall thicknesses in classes which are Class A, Class C, Class D, and Class E. Several properties of tubing such as inside diameter, wall thickness, specific gravity, tensile strength, elongation, dielectric breakdown voltage, dimensional stability, and heat resistance shall be determined by subjecting it to different test methods.1.1 The tubing is intended for electrical, mechanical, chemical, and medical applications manufactured from extrusion resins made from the copolymer of tetrafluoroethylene and hexafluoropropylene (FEP-fluorocarbon). This specification is for virgin material only and does not address recycled material as it is not appropriate for FEP tubing.NOTE 1: Abbreviations are in accordance with Terminology D1600.NOTE 2: There is no known ISO eqivalent to this standard.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D3296-14a(2019)
标准名称:
Standard Specification for FEP-Fluorocarbon Tube
英文名称:
Standard Specification for FEP-Fluorocarbon Tube标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D6513-21 Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Resistance Tests
- ASTM D6514-03(2019)e1 Standard Test Method for High Temperature Universal Oxidation Test for Turbine Oils
- ASTM D6515-00(2023)e1 Standard Test Method for Rubber Shaft Seals Determination of Recovery From Bending
- ASTM D6520-18 Standard Practice for the Solid Phase Micro Extraction (SPME) of Water and its Headspace for the Analysis of Volatile and Semi-Volatile Organic Compounds
- ASTM D6522-20 Standard Test Method for Determination of Nitrogen Oxides, Carbon Monoxide, and Oxygen Concentrations in Emissions from Natural Gas-Fired Reciprocating Engines, Combustion Turbines, Boilers, and Process Heaters Using Portable Analyzers
- ASTM D6525/D6525M-18(2023) Standard Test Method for Measuring Nominal Thickness of Rolled Erosion Control Products
- ASTM D6528-24 Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Fine-Grained Soils
- ASTM D6529-22 Standard Test Method for Operating Performance of Continuous Electrodeionization Systems on Feeds from 50 μS/cm to 1000 μS/cm
- ASTM D653-22 Standard Terminology Relating to Soil, Rock, and Contained Fluids
- ASTM D6531-00(2019) Standard Test Method for Relative Tinting Strength of Aqueous Ink Systems by Instrumental Measurement
- ASTM D6534-18 Standard Practice for Determining the Peak Force-to-Actuate of a Mechanical Pump Dispenser
- ASTM D6535/D6535M-18 Standard Practice for Determining the Dip Tube Length of a Mechanical Pump Dispenser
- ASTM D6536/D6536M-18 Standard Practice for Measuring the Dip Tube Length of a Mechanical Pump Dispenser
- ASTM D6541-21 Standard Specification for HFC-236fa, 1,1,1,3,3,3–Hexafluoropropane, (CF3CH2CF3)
- ASTM D6544-21 Standard Practice for Preparation of Textiles Prior to Ultraviolet (UV) Transmission Testing