
【国外标准】 Standard Practice for Cyclic Fatigue Testing of Metal Tibial Tray Components of Total Knee Joint Replacements
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
4.1 This practice can be used to describe the effects of materials, manufacturing, and design variables on the fatigue performance of metallic tibial trays subject to cyclic loading for relatively large numbers of cycles.4.2 The loading of tibial tray designs in vivo will, in general, differ from the loading defined in this practice. The results obtained here cannot be used to directly predict in-vivo performance. However, this practice is designed to allow for comparisons between the fatigue performance of different metallic tibial tray designs, when tested under similar conditions.4.3 In order for fatigue data on tibial trays to be comparable, reproducible, and capable of being correlated among laboratories, it is essential that uniform procedures be established.1.1 This practice covers a procedure for the fatigue testing of metallic tibial trays used in knee joint replacements using a cyclic, constant-amplitude force. It applies to tibial trays that cover both the medial and lateral plateaus of the tibia. This practice may require modifications to accommodate other tibial tray designs.1.2 This practice is intended to provide useful, consistent, and reproducible information about the fatigue performance of metallic tibial trays with one unsupported condyle. The results are applicable to the laboratory test conditions and may not correlate with in vivo performance.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F1800-19e1
标准名称:
Standard Practice for Cyclic Fatigue Testing of Metal Tibial Tray Components of Total Knee Joint Replacements
英文名称:
Standard Practice for Cyclic Fatigue Testing of Metal Tibial Tray Components of Total Knee Joint Replacements标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- AS 2545-1987/Amdt 1-2000 Subcontract conditions
- AS 2550.10-2006/Amdt 1-2009 Cranes, hoists and winches - Safe use Mobile elevating work platforms
- AS 2550.7-1996/Amdt No. 1-1999 Cranes - Safe use - Builders' hoists and associated equipment
- AS 2582.7-1983/Amdt 1-1986 Complete, filled transport packages - Methods of test - Low pressure test
- AS 2593-1995/Amdt 1-1998 Boilers - Unattended and limited attendance
- AS 2593-2004 (R2016)/Amdt 1-2007 Boilers - Safety management and supervision systems
- AS 2613-2005 (R2016)/Amdt 1-2007 Safety devices for gas cylinders
- AS 2638-1991/Amdt 1-1993 Sluice valves for waterworks purposes
- AS 2638.1-1999/Amdt 1-2001 Sluice valves for waterworks purposes - Metal seated
- AS 2638.2-1999/Amdt 1-2001 Sluice valves for waterworks purposes - Resilient seated
- AS 2658-2008/Amdt 1-2009 LP Gas - Portable and mobile appliances
- AS 2666-1996/Amdt 1-1997 Pressure-sensitive adhesive label stock - Paper
- AS 2678.1-1987/Amdt 1-1988 Methods for the analysis of zinc sulphide concentrates - Determination of the zinc content of zinc sulphide concentrates and zinc oxide fumes (titrimetric solvent extraction method)
- AS 2718 (Pt 1 to 2)-1984 Plastics pipes and fittings for gas reticulation - Polyethylene - Outside diameter series
- AS 2726.1-1995/Amdt 1-1997 Chainsaws - Safety requirements - Chainsaws for general use