
【国外标准】 Standard Test Methods for Gravimetric Determination of Total Solvent Extractable Content (TSEC) of Solid Waste Samples (Withdrawn 2014)
本网站 发布时间:
2024-02-28
- ASTM D5368-13
- Withdrawn, No replacement
- 定价: 0元
- 在线阅读
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 The TSEC provides a quantitative measure of the total solvent extractable organic content of the solid waste in question. Based upon the TSEC, the extract may be analyzed or further processed (that is, further cleanup or solvent concentration) in preparation for analysis. Thus, the TSEC provides a quantitative measure for optimizing the extractable organic concentration prior to chemical analysis.5.2 The TSEC of soil or waste material may be used as a quantitative measure for the screening and selection of samples for chemical analysis.5.3 The TSEC may be useful as a simple and relatively inexpensive quantitative indicator of changes occurring in the total extractable organic content of soil or waste materials.5.4 The detection limit of the TSEC depends upon the specific procedures employed. Typical detection limits in solvent extracts (that is, without solvent pre-concentration) for Method A are more than 1000 μg/g. For Method B typical detection limits are 20 to 100 μg/g in the solvent extract. For Method C the typical detection limits are 3 to 20 μg/g for solutes in the solvent extract.5.5 The sensitivity of the methods can be adjusted by varying the volume of solvent extract prior to gravimetric residue determination.1.1 These test methods describe standard procedures for gravimetrically determining the total nonvolatile and semi-volatile organic content of solvent extracts from soils or solid wastes. The following methods are included: Section Method A—Micro-Determination of TSEC 11-13 Method B—Evaporating Dish Procedure 14-16 Method C—Boiling Flask Procedure 17-191.2 These methods are used after a solvent extract is obtained from a soil or solid waste. For these methods to be applicable, the extraction solvent must have a boiling point less than that of water at ambient pressure.1.3 The total solvent extractable content (TSEC) of a soil, sediment, sludge, or solid waste depends upon the solvent and method used for the extraction procedure.
标准号:
ASTM D5368-13
标准名称:
Standard Test Methods for Gravimetric Determination of Total Solvent Extractable Content (TSEC) of Solid Waste Samples (Withdrawn 2014)
英文名称:
Standard Test Methods for Gravimetric Determination of Total Solvent Extractable Content (TSEC) of Solid Waste Samples (Withdrawn 2014)标准状态:
Withdrawn, No replacement-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM D5367-16(2021) Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted
- 下一篇: ASTM D5369-93(2008)e1 Standard Practice for Extraction of Solid Waste Samples for Chemical Analysis Using Soxhlet Extraction (Withdrawn 2016)
- 推荐标准
- ASTM D6014-00(2023) Standard Test Method for Determination of Dynamic Water Absorption of Leather Surfaces
- ASTM D6016-17(2023) Standard Test Method for Determination of Nitrogen, Water Extractable in Leather
- ASTM D6017-97(2020)e1 Standard Test Method for Determination of Magnesium Sulfate (Epsom Salt) in Leather
- ASTM D6021-22 Standard Test Method for Measurement of Total Hydrogen Sulfide in Residual Fuels by Multiple Headspace Extraction and Sulfur Specific Detection
- ASTM D6022-19 Standard Practice for Calculation of Permanent Shear Stability Index
- ASTM D6023-16 Standard Test Method for Density (Unit Weight), Yield, Cement Content, and Air Content (Gravimetric) of Controlled Low-Strength Material (CLSM)
- ASTM D6024/D6024M-16 Standard Test Method for Ball Drop on Controlled Low Strength Material (CLSM) to Determine Suitability for Load Application
- ASTM D6027/D6027M-24 Standard Practice for Calibration/Verification of Linear Displacement Transducers for Geotechnical Purposes
- ASTM D6028/D6028M-20 Standard Practice for (Analytical Procedure) Determining Hydraulic Properties of a Confined Aquifer Taking into Consideration Storage of Water in Leaky Confining Beds by Modified Hantush Method
- ASTM D6029/D6029M-20 Standard Practice for (Analytical Procedures) Determining Hydraulic Properties of a Confined Aquifer and a Leaky Confining Bed with Negligible Storage by the Hantush-Jacob Method
- ASTM D6031/D6031M-24 Standard Test Method for Logging In Situ Moisture Content and Density of Soil and Rock by the Nuclear Method in Horizontal, Slanted, and Vertical Access Tubes
- ASTM D6032/D6032M-17 Standard Test Method for Determining Rock Quality Designation (RQD) of Rock Core
- ASTM D6033-16 Standard Guide for Describing the Functionality of a Groundwater Modeling Code
- ASTM D6039/D6039M-18 Standard Specification for Open and Covered Wood Crates
- ASTM D6040-18(2023) Standard Guide to Standard Test Methods for Unsintered Polytetrafluoroethylene (PTFE) Extruded Film or Tape