【国外标准】 Standard Test Method of Measurement of Common-Emitter D-C Current Gain of Junction Transistors (Withdrawn 2011)
本网站 发布时间:
2024-02-28
- ASTM F528-99(2005)
- Withdrawn, No replacement
- 定价: 0元 / 折扣价: 0 元
- 在线阅读
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
The current gain of a transistor is basic to its operation and is its single most important parameter. Ionizing radiation, that is, gamma radiation due to a nuclear burst, will degrade the current gain due to lifetime damage in the bulk material. Degradation of gain will be greatest immediately following a burst of ionizing radiation and the gain will rapidly recover to a quasi steady-state value. Defect annealing may continue for weeks but usually the current gain recovery is small or negligible. This method provides a procedure that does not require special-purpose test equipment. This method is suitable for use for specification acceptance, service evaluation, or manufacturing control.1.1 This test method covers the measurement of common-emitter d-c current gain (forward, hFE, or inverted, hFEI) of bipolar transistors, for which the collector-emitter leakage current, ICEO, is less than 10% of the collector current, IC, at which the measurement is to be made, and for which the shunt leakage current in the base circuit is less than 10% of the base current required. 1.2 This test method is suitable for measurement of common-emitter d-c current gain at a single given value of test transistor collector current or over a given range of collector currents (for example, over the range of the transistor to be tested). 1.2.1 The nominal ranges of collector current over which the three test circuits are intended to be used are as follows: 1.2.1.1 Circuit 1, less than 100 [mu]A, 1.2.1.2 Circuit 2, from 100 [mu]A to 100 mA, and 1.2.1.3 Circuit 3, greater than 100 mA. 1.3 This test method incorporates tests to determine if the power dissipated in the transistor is low enough that the temperature of the junction is approximately the same as the ambient temperature. 1.4 The values stated in International System of Units (SI) are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address the safety problems, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
标准号:
ASTM F528-99(2005)
标准名称:
Standard Test Method of Measurement of Common-Emitter D-C Current Gain of Junction Transistors (Withdrawn 2011)
英文名称:
Standard Test Method of Measurement of Common-Emitter D-C Current Gain of Junction Transistors (Withdrawn 2011)标准状态:
Withdrawn, No replacement-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- BS EN IEC 61753-081-02:2023 Fibre optic interconnecting devices and passive components. Performance standard