5.1 The emission of mercury during crude oil refining is an environmental concern. The emission of mercury may also contaminate refined products and form amalgams with metals, such as aluminum.5.2 When representative test portions are analyzed according to this procedure, the total mercury is representative of concentrations in the sample.1.1 This test method covers the procedure to determine the total mercury content in a sample of crude oil. This test method can be used for total mercury determination in natural and processed liquid and oil products (gasoline, naphtha, etc.).1.2 This test method may be applied to samples containing between 5.0 ng/mL to 350 ng/mL of mercury. The results may be converted to mass basis.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This work has been published in “Determination of Mercury in Crude Oil by Atomic Spectroscopy.”21.5 WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use Caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 The emission of mercury during crude oil refining is an environmental concern. The emission of mercury may also contaminate refined products and form amalgams with metals, such as aluminum.5.2 When representative test portions are analyzed according to this procedure, the total mercury is representative of concentrations in the sample.1.1 This test method covers the procedures to determine the total mercury content in a sample of crude oil.1.2 The test method may be applied to crude oil samples containing between 5 ng/mL to 400 ng/mL of mercury. The results may be converted to mass basis, and reported as ng/g of mercury.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This work has been published in “Determination of Mercury in Crude Oil by Atomic Spectroscopy.”21.5 WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use Caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers hot-wrought and cold-finished special quality carbon steel bars, in straight lengths only, subject to mechanical property requirements and intended for use in manufacturing components for pressure piping and other pressure-containing applications. The steel bars are furnished in Grade B and Grade C and shall be made by melting, deoxidation, hot and cold working, heat treatment, and shall have special quality. Heat and product analyses shall be performed on the material and the chemical composition shall conform to the values required in carbon, manganese, phosphorus, sulfur, silicon, and lead. The carbon steel shall undergo tensile testing and conform to the required tensile strength, yield strength, and elongation.1.1 This specification2 covers hot-wrought and cold-finished special quality carbon steel bars, in straight lengths only, subject to mechanical property requirements and intended for use in manufacturing components for pressure piping and other pressure-containing applications.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers requirements for multiplayer pipe type 2 and compression fittings for hot and cold drinking water systems. Multilayer pipe type 2 is produced using a butt-welded aluminum pipe as a core, with an extruded inside layer of crosslinked polyethylene (PEX). An adhesive layer is used to bond the inside layer to the wall of the aluminum pipe. An outer layer of polyethylene (PE) and an adhesive layer are extruded to the outer wall of the aluminum pipe. This specification includes compression fittings and thread or solder adapters for use with pipe and fittings. The pipe dimensions, compression-fitting dimensions, burst pressure, thermal cycling, and excessive temperature-pressure capability shall be in conformance to the specification.1.1 This specification covers requirements for multilayer pipe type 2 and compression fittings for hot and cold drinking-water systems, with a maximum pressure rating of 1000 kPa (145 psi) at 82°C (180°F).Note 1—Multilayer Pipe Type 2Construction-based pressure rated pipe comprising more than one layer in which at least 60 % of the wall thickness is polymeric material.1.2 Multilayer pipe type 2 is produced using a butt-welded aluminum pipe as a core, with an extruded inside layer of crosslinked polyethylene (PEX). An adhesive layer is used to bond the inside layer to the wall of the aluminum pipe. An outer layer of polyethylene (PE) and an adhesive layer are extruded to the outer wall of the aluminum pipe.1.3 Multilayer pipe type 2 is produced in configurations 1 and 2, as referenced in Fig. 1.1.4 This specification includes compression fittings, which are referenced in Fig. 2 .1.5 Specifications for thread or solder adapters for use with pipe and fittings meeting the requirements of this specification are given in Annex A1 and Annex A2.1.6 The following precautionary caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

定价： 0元 / 折扣价： 0 元

This specification covers the standard for cold rolled ultra high strength carbon steel sheet in coils or cut lengths. The sheet shall be produced from aluminum killed steel and shall undergo continuous annealing to austenitic temperatures and then be water quenched. Cast or heat analysis shall conform to the prescribed chemical composition requirements in carbon, manganese, phosphorus, sulfur, and aluminum. Tension test shall be done on the point immediately adjacent to the material to be tested and properties shall conform to the specified tensile strength. The sheet shall have a matte surface finish texture and shall have cut edges. Unless otherwise specified, the sheet shall undergo oiling.1.1 This specification covers a cold rolled ultra high strength carbon steel sheet in coils or cut lengths. The product is available in five strength levels. The steel's strength is obtained by water quenching from an austenitic temperature resulting in a martensitic microstructure. This product is intended for miscellaneous applications where ultra high strength, weight saving, and good weldability are important.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 605元 / 折扣价： 515 元

1.1 This specification describes requirements and test methods for the qualification of PE and PP plastic bodied mechanical fittings intended to join cold water service pipe and tubing of NPS 3 or less. This includes plastic mechanical fittings intended for use on pipe and tubing covered by the following standards: D3035, D2737, D2239, F876, D2239, F2769, AWWA C901, and AWWA C904. Also, included in this specification are requirements for materials and qualification testing.1.2 Plastic mechanical fittings for hot and cold-water systems inside buildings as well as for district heating applications are not covered by this specification.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 605元 / 折扣价： 515 元

This specification covers metallic-coated, painted metallic-coated, and painted nonmetallic-coated steel sheet used in the manufacture of cold-formed framing members, such as, but not limited to, studs, joists, purlins, girts, and track. The steel sheet is available in the following designations: Structural Grade 50 Type H (ST50H), Structural Grade 340 Type H [ST340H], Structural Grade 40 Type H (ST40H), Structural Grade 275 Type H [ST275H], Structural Grade 37 Type H (ST37H), Structural Grade 255 Type H [ST255H], Structural Grade 33 Type H (ST33H), Structural Grade 230 Type H [ST230H], Structural Grade 50 Type L (ST50L), Structural Grade 340 Type L [ST340L], Structural Grade 40 Type L (ST40L), Structural Grade 275 Type L [ST275L], Structural Grade 37 Type L (ST37L), Structural Grade 255 Type L [ST255L], Structural Grade 33 Type L (ST33L), Structural Grade 230 Type L [ST230L], Nonstructural Grade 33 (NS33), and Nonstructural Grade 230 [NS230]. The ordered thickness shall be the base metal thickness. The base metal shall conform to the chemical composition requirements prescribed for carbon, manganese, phosphorus, sulfur, copper, nickel, chromium, molybdenum, vanadium, columbium, and titanium, as determined by heat and product analyses. Mechanical and corrosion tests shall be performed as prescribed. The base metal shall also conform to the mechanical property requirements including yield strength, tensile strength, and elongation. Coating requirements such as coating weight [mass], corrosion standard, thickness, flexibility and adhesion, are specified.1.1 This specification covers coated steel sheet used in the manufacture of cold-formed framing members, such as, but not limited to, studs, joists, purlins, girts, and track.1.2 The steel sheet used for cold-formed framing members includes metallic-coated, painted metallic-coated, or painted nonmetallic-coated.1.3 The values stated in either inch-pound or SI units shall be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other.1.4 Unless the order specifies the “M” designation [SI units], the product shall be furnished to inch-pound units.1.5 The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.1.6 Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification A924/A924M, unless otherwise provided herein.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers backer material, either in rod or strip form, for use with cold- and hot-applied joint sealant in portland-cement concrete or asphalt-pavement joints. Sealant backer material is available in three types: Type I, Type II, and Type III, and serves one or more of the following purposes: (1) limits the amount and depth of sealant applied to a joint, (2) acts as a barrier interface to prevent backside adhesion (bondbreaker), and (3) provides a form to assist the sealant in developing a shape factor. The material shall be easily compressed and installed in the joint reservoir and shall be heat resistant when used with hot-applied sealants. Physical properties of the material shall conform to the specified requirements for (1) density, (2) tensile strength, (3) water absorption, (3) compression deflection force, (4) compression recovery, (5) heat resistance, and (6) maximum shrinkage. The test specimen, test procedure, apparatus, and calculations for the physical properties enumerated are detailed.1.1 This specification covers backer material for cold- and hot-applied joint sealant for use in portland cement concrete or asphalt pavement joints.1.2 This specification establishes basic requirements for sealant backer material, either in rod or strip form, that can withstand the temperature of hot- or cold-applied sealants without excessive deformation.1.3 Sealant backer material serves one or more of the following purposes:1.3.1 Limits the amount and depth of sealant applied to a joint,1.3.2 Acts as a barrier interface to prevent backside adhesion (bond breaker), and1.3.3 Provides a form to assist the sealant in developing a shape factor.1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information purposes only.1.5 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This practice is intended solely for the evaluation of metallic-coated, painted metallic-coated, and painted nonmetallic-coated materials used for the manufacture of cold formed framing members.5.2 Correlation and extrapolation of corrosion performance based on exposure to the test environment provided by Practice B117 are not always predictable. Correlation and extrapolation should be considered only in cases where appropriate corroborating long-term atmospheric exposures have been conducted.5.3 This practice assesses whether coated materials not currently in Specification A1003/A1003M satisfy the required minimum corrosion characteristics.1.1 This practice covers procedures for establishing the acceptability of metallic-coated steel sheet, painted metallic-coated steel sheet, and painted nonmetallic-coated steel sheet for use as cold formed framing members.1.2 This practice shall be used to assess the corrosion resistance of different coatings on steel sheet in a laboratory test. It shall not be used as an application performance standard for the cold formed framing members.1.3 The practice shall be used to evaluate coatings under consideration for addition to Specification A1003/A1003M.1.4 The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.1.5 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of the standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers cold-rolled, carbon steel sheets, in coils and cut lengths, in the following designations: commercial steels (CS Types A, B, and C); drawing steel (DS Types A and B); deep drawing steel (DDS); extra deep drawing steel (EDDS); structural steel (SS Grades 25[170], 30[205], 33[230] Types 1 and 2, 40[275] Types 1 and 2, 50[340], 60[410], 70[480], and 80[550]); high-strength low-alloy steel (HSLAS Classes 1 and 2 of Grades 45[310], 50[340]. 55[380], 60[410], 65[450], and 70[480]), high-strength low-alloy steel with improved formability (HSLAS-F Grades 50[340], 60[410], 70[480], and 80[550]); solution hardened steel (SHS); and bake hardenable steel (BHS). Conformance of the steel sheets to chemical composition requirements shall be tested by heat analysis. Specimens shall also undergo tension and bending tests and shall conform to specified values of tensile and yield strength, elongation, and bake hardening index. Unless otherwise indicated, sheet surfaces shall have a matte finish and shall be oiled.1.1 This specification covers cold-rolled, carbon, structural, high-strength low-alloy, high-strength low-alloy with improved formability, required hardness, full hard, solution hardened, and bake hardenable steel sheet, in coils and cut lengths.1.2 Cold rolled steel sheet is available in the designations as listed in 4.1.1.3 This specification does not apply to steel strip as described in Specification A109/A109M.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1.1 This specification covers high-strength, low-alloy, hot-rolled steel sheet and strip and cold-rolled sheet having improved formability when compared with steels covered by Specifications A 606 and A 607. The product is furnished as either cut lengths or coils and is available in four-strength levels, Grades 50, 60, 70, and 80 (corresponding to minimum yield strength (see Table 1)). The steel is killed, made to a fine grain practice, and includes microalloying elements such as columbium, titanium, vanadium, zirconium, etc. The steel may be treated to achieve inclusion control. The product is intended for structural and miscellaneous applications where higher strength, savings in weight, improved formability, and weldability are important.1.2 The values stated in inch-pound units are to be regarded as the standard.

定价： 0元 / 折扣价： 0 元

3.1 This practice establishes a multiple person cold water survival/rescue procedure.3.2 All persons who are identified as water rescuers shall meet the requirements of this practice.3.3 This practice is intended to assist government agencies, state, local, or regional organizations; fire departments; and rescue teams and others who are responsible for establishing a minimum performance for personnel who respond to water emergencies.3.4 The majority of the rescuers performing this technique must be wearing personal flotation devices. These devices should conform to standards set by the appropriate national regulatory authority, that is, the U.S. Coast Guard in the United States, and be in good and serviceable condition.3.5 A water rescuer sometimes may be immersed in cold water for prolonged periods of time. They are unable to get to shore or shore is too far away, rescue is not imminent, no boat is available to get into or on top of, and no flotsam is available. The water rescuer needs to assume a defensive posture to conserve heat and increase survival time.1.1 This practice covers the recommended water rescue procedure for performing the huddle position.1.2 This practice is one in a set of self-rescue techniques for the water rescuer.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 This practice establishes a single person cold water survival/rescue procedure.3.2 All persons who are identified as water rescuers shall meet the requirements of this practice.3.3 This practice is intended to assist government agencies, state, local, or regional organizations; fire departments; and rescue teams and others who are responsible for establishing a minimum performance for personnel who respond to water emergencies.3.4 A rescuer needs to be wearing a personal flotation device to perform this technique. These devices should conform to standards set by the appropriate national regulatory authority, that is, the U.S. Coast Guard in the United States, and be in good and serviceable condition.3.5 A water rescuer sometimes may be immersed in cold water for prolonged periods of time. They are unable to get to shore or shore is too far away, rescue is not imminent, no boat is available to get into or on top of, and no flotsam is available. The water rescuer needs to assume a defensive posture to conserve heat and increase survival time.1.1 This practice covers the recommended water rescue procedure for performing the heat escape lessening posture (HELP) position.1.2 This practice is one in a set of self-rescue techniques for the water rescuer.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车