AbstractThese specifications cover the design and performance requirements, and associated test procedures for helmets used in the activities of skateboarding and trick roller skating. When tested, the helmets shall meet specified requirements for the peak acceleration and time duration, headforms and sizes, anvils for impact (flat, cylindrical hazard, and triangular hazard anvils), dynamic strength retention system, and impact sites, velocity, and schedule.1.1 This specification covers performance requirements for helmets to be used in the activities of skateboarding and trick roller skating.1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein.1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the headgear meets all of the requirements of the specification in their entirety. A headgear that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be sold with any indication that it meets parts of the specification.1.4 This standard is subject to revision at any time by ASTM. It must be reviewed every five years and if not revised either reapproved or withdrawn. References to the standard must include the version date. No references to a version that has been replaced or withdrawn shall be placed on any product or its packaging manufactured more than 24 months after the effective revision or withdrawal date. Go to astm.org to verify the latest version of this standard.1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1. Scope 1.1 This Standard applies to helmets intended for use in ice hockey. The objective of the standard is to reduce the risk of head injury to ice hockey participants, when the helmet is used as intended and in accordance with the manufacturer's

定价： 319元 / 折扣价： 272 元

This PDF includes GI #2 and #3. 1. Scope 1.1 This Standard applies to helmets intended to provide protection for the heads of cyclists and defines the areas of the head that are to be protected. It covers the basic performance requirements for shoc

定价： 410元 / 折扣价： 349 元

This specification covers the performance requirements for helmets used as protective head gear in pole vaulting. Prior to testing, samples should be conditioned in ambient, low temperature, high temperature, and water immersion conditions. The products should be tested using flat and curbstone anvils on any site on or above the test line with peak acceleration not exceeding the specified values. Both lateral and upward visual clearances should be sufficiently unobstructed.1.1 This specification covers performance requirements for helmets to be used in the activity of pole vaulting.1.2 All testing and requirements of this specification are to be carried out in accordance with Test Methods F1446 except where noted in this specification.1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the product meets all of the requirements of the specification in their entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed the specification and shall not be sold with any indication that it meets parts of the specification.1.4 Helmets designed to comply with this and other standards may proclaim uses as certified by the manufacturer.1.5 The values stated in SI units are to be regarded as the standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

4.1 The purpose of this standard is to provide reliable and repeatable compression test methods for the evaluation of helmets used in law enforcement, corrections, and military applications.4.2 It is anticipated that this standard will be referenced by certifiers, purchasers, or other users in order to meet their specific needs. Those users will specify which test methods apply and will specify any performance categories or levels.1.1 This standard provides test methods for assessing compression resistance of helmets worn by military, law enforcement, and corrections personnel. These test methods are applicable for many styles of helmet (that is, high-cut, mid-cut, full-cut).1.2 Three compression test methods are included: (1) top-to-bottom, (2) side-to-side, and (3) front-to-back.1.3 It is anticipated that this standard will be referenced by suppliers, certifiers, purchasers, or other users to meet their specific needs. Those users will specify, in other standards and specifications, which test methods and conditioning procedures are applicable and will specify any performance categories or levels.1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 546元 / 折扣价： 465 元

This specification covers the performance requirements for helmets used by short track speed ice skaters (excluding hockey). The performance requirements to which the helmets shall conform include those for the headform, retention system, impact sites and projections, and impact schedule.1.1 This specification covers performance requirements for helmets used by long track and short track speed ice skaters (excluding hockey). This specification recognizes the desirability of lightweight construction and ventilation; however, it is a performance standard and is not intended to restrict design.1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein.1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification must be a certification that the headgear meets all of the requirements of the specification in their entirety. A headgear that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be sold with any indication that it meets parts of the specification.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 The purpose of this specification is to specify performance requirements, conditioning procedures, and test methods for nonballistic-resistant head protection used in public order police applications.4.2 It is anticipated that this specification will be referenced by certifiers, purchasers, or other users in order to meet their specific needs.1.1 This specification specifies performance requirements, conditioning procedures, and test methods for assessing nonballistic-resistant head protection (that is, helmet and face shield) specifically designed to be worn by law enforcement and corrections officers when maintaining order in violent situations.1.2 This specification does not address eye protection other than face shields that are attached to the helmet.1.3 The threats and hazards addressed in this specification were identified by officers specially trained and equipped to manage any form of public gathering, ranging from concerts, parades, marches, and demonstration events to violent unrest.1.4 It is anticipated that this specification will be referenced by suppliers, certifiers, purchasers, or other users to meet their specific needs.1.5 The user of this specification may choose to specify additional requirements, and some options are provided in Appendix X1.1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

Update #1 was published as notification that this is now a National Standard of Canada. This PDF includes Update #1 1 Scope 1.1 This Standard applies to helmets and faceshields intended to provide protection to the heads and faces of law correct

定价： 592元 / 折扣价： 504 元

4.1 The purpose of these test methods is to provide reliable and repeatable nonballistic test methods and conditioning procedures for the evaluation of head protection used in law enforcement and corrections applications.4.2 It is anticipated that these test methods will be referenced by certifiers, purchasers, or other users in order to meet their specific needs. Those users will specify which test methods and conditioning procedures are applicable, and will specify any performance categories or levels.4.3 These test methods include some procedures and references to other standards to ensure that relevant properties are addressed.1.1 This standard provides nonballistic test methods and conditioning procedures for assessing head protection (that is, helmet and face shield) worn by law enforcement and corrections officers.1.1.1 Conditioning procedures are included to assess durability in terms of resistance to chemicals and cleaning products, extreme temperatures, weathering, and absorption of liquids.1.1.2 Test methods are included to assess the protective performance against hazards including impact/bump, projectiles (other than bullets), flame, and liquids.1.1.3 Test methods are included to assess safety and ergonomic aspects of retention system strength, stability of the helmet on the wearer’s head, corrosion resistance, and face shield visual acuity, field of view, scratch resistance, and anti-mist properties.NOTE 1: These test methods reference published standards from ASTM International and other standards developing organizations. Appendix X1 contains a summary of test methods included in this standard, along with the source and purpose for each.1.2 These test methods do not address eye protection other than face shields that are attached to the helmet.1.3 It is anticipated that these test methods will be referenced by suppliers, certifiers, purchasers, or other users to meet their specific needs. Those users will specify, in other standards and specifications, which test methods and conditioning procedures are applicable and will specify any performance categories or levels.1.3.1 If there is a discrepancy between these test methods and a user-supplied document, the user-supplied document shall take precedence.1.4 In these test methods, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of these test methods. Purchasers and other users are responsible for the “other standards and specifications” and for specifying any requirements that supersede those of these test methods.1.5 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

This specification covers the performance requirements for helmets manufactured for use by infants and toddlers as passengers or operators of non-motorized wheeled vehicles. The performance requirements to which the helmets shall conform include those for headforms, peripheral vision, retention system testing, anvils and impact velocities, impact sites, impacting schedule, and peak acceleration.1.1 This specification covers performance requirements for helmets manufactured for use by infants and toddlers as passengers or operators of nonmotorized vehicles intended for their use. This specification recognizes the desirability of lightweight construction and ventilation; however, it is a performance standard and is not intended to restrict design.1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446 except as noted.1.3 Partial utilization of this standard is prohibited. Any statement of compliance with this specification must be a certification that the product meets all of the requirements of this specification in their entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this standard, and should not be sold with any indication that it meets parts of this standard.1.4 Headgear that complies with this and other standards may proclaim uses as described in those standards as certified by the manufacturer.1.5 This standard is subject to revision at any time by ASTM. It must be reviewed every five years and if not revised either reapproved or withdrawn. References to the standard must include the version date. No references to a version that has been replaced or withdrawn shall be placed on any product or its packaging manufactured more than 24 months after the effective revision or withdrawal date. Go to astm.org to verify the latest version of this standard.1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车