Update #1 was published as notification that this is now a National Standard of Canada This PDF includes Update #1 1. Scope 1.1 This Standard is intended for manufacturers and purchasers of machinery sold in, or exported from, Canada. It is also

定价： 546元 / 折扣价： 465 元

1. Scope This International Standard establishes the classification of the major types of winches and rope anchors and the nomenclature for major components and parts peculiar to these machines. Examples used here are not intended to include all exis

定价： 319元 / 折扣价： 272 元

1. Scope This International Standard specifies a laboratory method for vibration testing of operator seats for earth-moving machinery at frequencies between 1 Hz and 20 Hz. It is based on ISO 10326-1 which is a general method applicable to seats for

定价： 410元 / 折扣价： 349 元

定价： 728元 / 折扣价： 619 元

定价： 481元 / 折扣价： 409 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

5.1 Chemical-resistant polymer machinery grouts are used to provide precision support for machinery or equipment.NOTE 2: The machinery or equipment or support bases or plates, or combination thereof, are positioned to the precise elevation and location required. The bases or plates are typically placed on prepared foundations and supported on temporary shims or support bolts (jack screws). Forms are installed to contain the flowable grout. The grout is poured around the perimeter in such a manner as to allow the grout to flow around and under the equipment base or plates. The grout subsequently hardens to provide a strong rigid support layer capable of withstanding the stresses transferred by the equipment to the foundation. Although the actual machinery base plate is typically metal and the cover plate in this test uses acrylic glass, different grouts using acrylic glass cover plates has proven useful for comparative purposes as described in this test in laboratory conditions.5.2 In addition to the required physical properties of the grout, the flow and bearing area achieved are important considerations for effective grout installation. The two characteristics measured by this test method are flow and bearing area.5.3 The flow test simulates typical application conditions for a flowable polymer machinery grout in a laboratory environment. It may be used to evaluate the suitability of a particular grout for a specific application, to compare the flowability and bearing area of two or more grouts, or to evaluate the effects of formulation changes, temperature, mixing techniques, or other factors on flowability.5.4 The estimated amount of upper grout surface contact in percent can be used to compare two or more grouts or show the effects of temperature, formulation changes, or other factors on bearing area. A limited set of results using visual guides (see Fig. 1 and Fig. 2) is used to classify the bearing as “high”—greater than 85 %,” “medium—70 to 85  %,” and “low—less than 70 %.”1.1 This test method covers the measure of flowability of chemical-resistant polymer machinery grouts as evaluated in a 50-mm [2-in.] or 25-mm [1-in.] pour thickness in a laboratory setting. The test method provides for the assessment of upper surface plate contact area (bearing area). These grouts will typically be at least two component formulations that may be used for installations where grout thickness will range from 25 to 150 mm [1 to 6 in.] underneath the base or plates being grouted.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

3.1 This practice provides the three principal methods of fitting chocks to marine machinery foundations to ensure that the machinery is free of vibration and perfectly aligned after installation.3.1.1 The three principal methods of installing chocks described herein are as follows:3.1.1.1 Type A—Epoxy-based resin, nonshrinking, and3.1.1.2 Type B—Two-piece wedge chocks.3.1.1.3 Type C—Solid, one-piece fitted chocks.1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations.1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1. Scope This International Standard establishes general principles for the design and application of safety signs and hazard pictorials permanently affixed to tractors, machinery for agriculture and forestry, and powered lawn and garden equipment as d

定价： 1229元 / 折扣价： 1045 元

定价： 525元 / 折扣价： 468 元 加购物车

定价： 1074元 / 折扣价： 956 元 加购物车

定价： 350元 / 折扣价： 312 元 加购物车

定价： 525元 / 折扣价： 468 元 加购物车