This specification covers aluminum pigments in powder and paste forms for use in paints. The aluminum pigments are available in four types, as follows: Type I, leafing powder; Type II, leafing paste; Type III, nonleafing powder; and Type IV, nonleafing paste. Each type is grouped into three classes based on residue retained on a No. 325 sieve, as follows: Class A, fine; Class B, medium; and Class C, coarse. Materials shall be sampled, tested, and conform accordingly to composition of non-volatile matter, easily extracted fatty and oily matter (polishing lubricant), total impurities other than fatty and oily matter, coarse particles as total residue retained, and leafing ability.1.1 This specification covers four types and three classes of aluminum pigments for use in paints.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification establishes the properties and requirements for chlorinated and chlorinated-brominated copper phthalocyanine green pigments in dry powder form, for use in paints, printing inks, and related products. The pigments may or may not phthalocyanine blue or other ingredients incorporated during manufacture to improve or alter the properties of the pigment, but free of any other coloring matter either organic or inorganic. Specimens shall be sampled and undergo tests as appropriate, and shall conform to the following properties: moisture and other volatile matter; mass color, tint character, and tinting strength; oil absorption; basic dye derivatives; chrome green and iron blue; and reaction in identification test.1.1 This specification covers chlorinated and chlorinated-brominated copper phthalocyanine green pigments in dry powder form, for use in paints, printing inks, and related products. A variety of commercial types are available to meet the requirements of different end uses.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This test method is a way of testing the color and strength of pigments by use of a miniature sandmill. It correlates well with industrial practice and is used for routine quality control.1.1 This test method covers the determination, through the use of a miniature sandmill, of the color and strength of dry color pigments.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.

定价： 0元 / 折扣价： 0 元

1.1 These test methods cover para red and toluidine red pigments (toners) in the dry form commercially known as "pure."1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.>

定价： 0元 / 折扣价： 0 元

5.1 This test method allows the user to make a determination of the blueness or yellowness of the tint undertone of titanium dioxide pigments, versus a reference pigment agreed upon by the parties to the test. This is an important measure of tone, since it gives both a measure of effective particle size, and quick approximation of the blue/yellow undertone that can be expected when a coating containing the titanium dioxide is tinted.5.2 Such matters as the vehicle for preparing the dispersions and the mechanical method of preparing the dispersion are left to the user. However, variation in these practices will lead to increased variance in the results, so users ought to fix these parameters, in-so-far as is possible, within any one laboratory. This will lead to reduced uncertainty of the results within that laboratory, and it is seldom that interlaboratory comparisons of this test result is needed.5.3 Each user must decide whether the loss of accuracy in his measurements due to variation of these parameters is negligibly small for the purpose for which the data are obtained.1.1 This test method is intended to be used to determine the tint undertone (blue or yellow) of titanium dioxide pigments. This relates to the effective particle size of the pigment1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 These test methods compile in one place, recommended procedures for analyzing inorganic colored pigments. These pigments are used extensively in paints, and for this reason their compositions are important to the formulators and user.1.1 These test methods cover procedures for the chemical analysis of yellow, orange, red, and brown pigments containing iron and manganese. The test methods apply specifically to the following pigments: synthetic hydrated yellow iron oxide, yellow ocher, red and brown iron oxides, raw and burnt umber, raw and burnt sienna, and venetian red.1.2 The analytical procedures appear in the following order:    ASTM    Method    Refer-Dry Pigments  Sections encesMoisture and Other Volatile Matter  6  D280Loss on Ignition  7  Coarse Particles  8  D185Matter Soluble in Water  9  D1208Organic Coloring Matter 10  Iron Oxide 11 and 12  Calcium Compounds (Reported as CaO) 13 and 14  Sulfates Soluble in Hydrochloric Acid 15 and 16  Lead Chromate (in Ochers) 17  Calcium Carbonate (in Venetian Red) 18  C25Manganese (in Siennas and Umbers) 19 and 20   Pigment Pastes in Oil     Pigment Content 21  D1208Moisture and Other Volatile Matter 22  D1208Nonvolatile Matter in Vehicle 23  Moisture by Distillation 24  D1208Coarse Particles and Skins 25  D185Consistency (Stormer) 26  D5621.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to us.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

3.1 This test method is used by black pigment producers and users for product acceptance.1.1 This test method covers the determination of the solvent-extractable material in black pigments such as carbon black, lampblack, and bone black.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This test method is used by titanium dioxide pigment manufacturers and users for process control and product acceptance.1.1 This test method covers the determination of the ratio of anatase to rutile in titanium dioxide pigments. The method is also applicable to pigment mixtures and pigmented coatings containing titanium dioxide.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 The oil absorption value obtained by this test method provides information about the vehicle demand of the pigment when it is used in a pigment paste. Oil absorption values can be used to characterize batches of a given pigment.4.2 This test method differs from Test Method D281 in that D281 requires a vigorous rubbing action whereas this test method involves only a gentle stirring and folding of the pigment. Because the end points are different, the values obtained from the two test methods generally differ.1.1 This test method covers the determination of oil absorption of pigments by the Gardner-Coleman procedure.21.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 Zinc yellow is used in rust-inhibiting protective coatings and metal primers for ferrous and non-ferrous metals.AbstractThis specification covers zinc yellow (zinc chromate) pigments used in rust-inhibiting protective coatings and metal primers for ferrous and non-ferrous metals. The two types of pigments include: Type I and Type II. The pigment shall conform to the required composition for zinc, chromium, sulfates, chlorides, alkaline slats, matter insoluble in acetic acid, moisture and other volatile matter, and coarse particles. The following tests shall be conducted: chemical analysis, coarse particles, and mass color and tinting strength.1.1 This specification covers the pigments commercially known as zinc yellow (zinc chromate).1.2 Two types are included:1.2.1 Type I—High-purity, low sulfate and chloride content.1.2.2 Type II—Regular grade.1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers red and brown pigments of dry and wet ground natural iron oxide, dry and wet ground calcined natural iron oxide, and mixtures of these with synthetic iron oxides. These pigments are suitable for such applications as paints and coatings. Specimens shall be sampled and suitably undergo chemical analysis for total iron oxide, sulfur as sulfates, organic coloring matter, matter soluble in water, coarse particles in dry pigment, and moisture and other volatile matter. The pigments shall also conform to specified mass color, tint character, and tinting strength as mutually agreed upon between purchaser and seller.1.1 This specification covers dry and wet ground naturally occurring iron oxide, dry and wet ground calcined naturally occurring iron oxide, and mixtures of these with synthetic iron oxides. These pigments are suitable for use in paints, coatings, and many other applications.1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 This compilation of available ASTM methods for the analysis of white pigment serves as a guide to chemists.1.1 This guide covers procedures for the chemical analysis of white pigments.1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This test method may be used in quality control laboratories when the repeated analysis of titanium dioxide in similar paints may be required. Reagents and time are kept to a minimum when this test method is used in place of wet chemical analysis such as in Test Methods D1394. However, reproducibility and repeatability are not as good as in Test Methods D1394.1.1 This test method covers the atomic absorption (AA) analysis of titanium dioxide content in pigments recovered from whole paint. It is applicable to quality control situations where the same type of product is repeatedly analyzed.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers three grades of pigment commercially known as calcium borosilicate composite pigment. The two types differ in chemical composition while the two classes of type I differ in oil absorption. The chemical composition, ignition loss, and particle size shall be tested to meet the requirements prescribed. The specific surface diameter of the pigment, oil absorption, and coarse particle shall be tested to meet the requirements prescribed.1.1 This specification covers three grades of pigment commercially known as calcium borosilicate composite pigment. The two types differ in chemical composition while the two classes of Type I differ in oil absorption.1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车