5.1 This test method is suitable for manufacturing control and for verifying that a product meets specifications. This test method provides rapid, multi-element determinations with sufficient accuracy to ensure product quality and to minimize production delays. The analytical performance data may be used as a benchmark to determine if similar X-ray spectrometers provide equivalent precision and accuracy, or if the performance of a particular X-ray spectrometer has changed.5.2 Calcium is sometimes added to steel to affect inclusion shape which enhances certain mechanical properties of steel. This test method is useful for determining the residual calcium in the steel after such treatment.5.2.1 Because calcium occurs primarily in inclusions, the precision of this test method is a function of the distribution of the calcium-bearing inclusions in the steel. The variation of determinations on freshly prepared surfaces will give some indication of the distribution of these inclusions.1.1 This test method covers the wavelength dispersive X-ray fluorescence analysis of low-alloy steels for the following elements:Element Mass FractionRange, %Calcium 0.001 to 0.007Chromium 0.04 to 2.5Cobalt 0.03 to 0.2Copper 0.03 to 0.6Manganese 0.04 to 2.5Molybdenum 0.005 to 1.5Nickel 0.04 to 3.0Niobium 0.002 to 0.1Phosphorus 0.010 to 0.08Silicon 0.06 to 1.5Sulfur 0.009 to 0.1Vanadium 0.012 to 0.61.1.1 Unless exceptions are noted, mass fraction ranges can be extended and additional elements can be included by the use of suitable reference materials and measurement conditions. Deviations from the published scope must be validated by experimental means. See Guide E2857 for information on validation options.1.2 The values stated in the International System of Units (SI) are to be regarded as standard. The values given in parentheses are mathematical conversions to other units that are provided for information only, because they may be used in older software and laboratory procedures.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 10.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 A pressure vessel surveillance program requires a methodology for relating radiation-induced changes in materials exposed in accelerated surveillance locations to the condition of the pressure vessel (see Practice E853). An important consideration is that the irradiation exposures be expressed in a unit that is physically related to the damage mechanisms.4.2 A major source of neutron radiation damage in metals is the displacement of atoms from their normal lattice sites. Hence, an appropriate damage exposure index is the number of times, on the average, that an atom has been displaced during an irradiation. This can be expressed as the total number of displaced atoms per unit volume, per unit mass, or per atom of the material. Displacements per atom is the most common way of expressing this quantity. The number of dpa associated with a particular irradiation depends on the amount of energy deposited in the material by the neutrons, and hence, depends on the neutron spectrum. (For a more extended discussion, see Practice E521.)4.3 No simple correspondence exists in general between dpa and a particular change in a material property. A reasonable starting point, however, for relative correlations of property changes produced in different neutron spectra is the dpa value associated with each environment. That is, the dpa values themselves provide a spectrum-sensitive index that may be a useful correlation parameter, or some function of the dpa values may affect correlation.4.4 Since dpa is a construct that depends on a model of the neutron interaction processes in the material lattice, as well as the cross section (probability) for each of these processes, the value of dpa would be different if improved models or cross sections are used. The calculated displacement cross section for ferritic iron, as given in this practice, is determined by the procedure given in 6.3. The currently recommended iron displacement cross section in this practice (Table 1) was generated using the ENDF/B-VI iron cross section (1).3 A recent calculation using ENDF/B-VII.0 produced identical results (2, 3). The iron cross section data in ENDF/B-VII.1 does not differ from ENDF/B-VII.0. Although the ENDF/B-VI based iron displacement cross section differs from the previously recommended ENDF/B-IV iron displacement cross section (1) by about 60 % in the energy region around 10 keV, by about 10 % for energies between 100 keV and 2 MeV, and by a factor of 4 near 1 keV due to the opening of reaction channels in the cross section, the integral iron dpa values are much less sensitive to the change in cross sections. The update from ENDF/B-IV to ENDF/B-VI dpa rates, when applied to the H. B. Robinson-2 pressurized water reactor, resulted in “up to ∼4 % higher dpa rates in the region close to the pressure vessel outer surface” and in “slightly lower dpa rates ... close to the pressure vessel inner wall” (4, 5). Table 2 presents a comparison of a previous edition (Practice E693–94) and currently recommended dpa estimates for several neutron spectra.(A) Energies represent the lower bin boundary. The upper bin limit is 20.0 MeV.(A) The spectrum-average dpa values in this table were computed using Eq 11 in a 640 SAND-II energy group representation and a lower integration bound of Eo = 10–10 MeV.1.1 This practice describes a standard procedure for characterizing neutron irradiations of iron (and low alloy steels) in terms of the exposure index displacements per atom (dpa) for iron.1.2 Although the methods of this practice apply to any material for which a displacement cross section σd(E) is known (see Practice E521), this practice is written specifically for iron.1.3 It is assumed that the displacement cross section for iron is an adequate approximation for calculating displacements in steels that are mostly iron (95 to 100 %) in radiation fields for which secondary damage processes are not important.1.4 Procedures analogous to this one can be formulated for calculating dpa in charged particle irradiations. (See Practice E521.)1.5 The application of this practice requires knowledge of the total neutron fluence and flux spectrum. Refer to Practice E521 for determining these quantities.1.6 The correlation of radiation effects data is beyond the scope of this practice.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

This specification covers unpigmented, unsupported, low-density polyethylene films (hereafter referred to as film or films) for general use and packaging applications. It is applicable to films made from polyethylene copolymers, and also applicable to films made from blends of homopolymers and copolymers, including ethylene/vinylacetate copolymers. The low-density polyethylene film shall be classified by Types 1, 2, and 3; Surfaces 1, 2, and 3; Classes 1, 2, 3, and 4; and Finishes 1, 2, 3, and 4. The film shall be made from an ethylene homopolymer, ethylene copolymers, or blends of homopolymers or copolymers, or homopolymer and copolymer, so that it meets the density and other film requirements specified. Tests shall be performed to conform to the specified properties of the material in accordance with the following test methods: conditioning; test conditions; thickness; yield; flatness; density; coefficient of friction; clarity; haze; wetting tension; impact resistance; tensile properties; heat sealability; and odor.1.1 This specification covers unpigmented, unsupported, low-density polyethylene and linear low-density polyethylene films (hereafter referred to as film or films) with densities ranging from 0.910-0.925 g/cm3 per Specification D4976.NOTE 1: The density of a film will not necessarily be equal to the density of a molded plaque from the same resin.NOTE 2: Blends of ethylene/vinyl acetate (EVA) with low-density polyethylene may have densities up to 0.929 g/cm3.1.2 This specification is applicable to homopolymer polyethylene, but is not restricted to it. It is applicable to films made from polyethylene copolymers, and also applicable to films made from blends of homopolymers and copolymers, including ethylene/vinyl acetate copolymers.1.3 The thickness of the films covered by this specification is 101.6 μm or less (0.004 in. or less), inclusive. The maximum width of the sheet or layflat is 3.30 m (130 in.).1.4 This specification does not cover oriented heat-shrinkable films.1.5 This specification allows for the use of recycled polyethylene film or resin as feedstock, in whole or in part, as long as all of the requirements of this specification are met and as long as any specific requirements as governed by the producer and end user are also met. (See Note 3.)NOTE 3: Guide D7209 describes terminology and definitions related to recycled plastics.1.6 This specification defines the levels of the various physical properties from which specifications for specific films may be described. The levels of physical properties required by a film for a given application are selected from Section 6. However, Sections 2 – 5 relating to tolerances shall apply without change to all film falling within the scope indicated by the title and 1.1 – 1.4.1.7 This specification covers dimensional tolerances, classifications, intrinsic quality requirements, and test methods. The dimensional tolerances include thickness, width, and length or yield. Classification defines types, classes, surfaces, and finishes. The intrinsic quality requirements include density, workmanship, tensile strength, heat sealability, and odor, as well as the classification properties for impact strength, coefficient of friction, optical properties, and surface treatment. A sampling method is included.1.8 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.9 The following precautionary caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.NOTE 4: There is no known ISO equivalent to this standard.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 This test method is applicable to organic solutions containing 20 to 2000 μg uranium per mL of solution presented to the spectrometer for the solution techniques or 200 to 50 000 μg uranium per g using the fused pellet technique.5.2 Either wavelength-dispersive or energy-dispersive XRF systems may be used, provided that the software accompanying the system is able to accommodate the use of internal standards.1.1 This test method covers the steps necessary for the preparation and analysis by X-ray fluorescence (XRF) of oils and organic solutions containing uranium. Two different preparation techniques are described.1.2 The procedure is valid for those solutions containing 20 to 2000 μg uranium per mL as presented to the spectrometer for the solution technique and 200 to 50 000 μg uranium per g for the pellet technique.1.3 This test method requires the use of an appropriate internal standard. Care must be taken to ascertain that samples analyzed by this test method do not contain the internal standard or that this contamination, whenever present, has been corrected for mathematically. Such corrections are not addressed in this procedure. Care must be taken that the internal standard and sample medium are compatible; that is, samples must be miscible with tri- n-butyl phosphate (TBP) and must not remove the internal standard from solution. Alternatively, a scatter line may be used as the internal standard.21.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 9 and Note 2.

定价： 702元 / 折扣价： 597 元 加购物车

This standard practice outlines procedures for conducting a form of low impact paintball games through the establishment of specific game rules and equipment requirements aimed at reducing the discomfort sometimes experienced by players. Like any other physical activity, paintball can cause injury, especially when players do not follow safety instructions. This practice establishes minimum safety requirements for the operation of Low Impact Paintball Playing Fields and covers basic paintball safety rules, field orientation and safety briefing, barrel blocking device regulation, goggles, chronographing procedures, required signs, emergency requirements, adequate staffing during games, fill station, and filling of paintball air systems and cylinders. It also covers adequate spectator provisions and staging area, protective barriers, game area requirements, low impact paintball markers, game rule restrictions, velocity restrictions, and paintball high pressure propellant gas storage vessel requirements.1.1 This practice establishes minimum safety requirements for the operation of Low Impact Paintball Playing Fields, and provides for certain required materials and procedures.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 Identification and Quantitation of Phthalates—DBP, BBP, DEHP, DNOP, DINP, and DIDP are representative of the phthalates either banned or being monitored by a variety of regulations. Regulations include: EU—Directive 2005/84/EC, US—Consumer Product Safety Improvement Act of 2008 – section 108, Japan—Health, Labor and Welfare Ministry guideline No. 336 (2010) and IEC 62321-8:2017. These test methods provide a procedure to identify and quantify phthalates in PVC.5.2 Other techniques successfully used to separate and identify phthalates in PVC include GC/MS, HPLC/UV, HPLC/MS, FTIR, and GC/FID (flame ionization detector).1.1 This test method provides a procedure to identify and quantify phthalates by thermal desorption (TD) gas chromatography (GC) mass spectrometry (MS). Six phthalates are used to demonstrate the use of the procedure: BBP, DBP, DEHP, DNOP, DINP and DIDP.1.2 Within the context of this method, “low level” is defined as 1000 ppm.1.3 The values in SI units are to be regarded as standard.1.4 This test method includes references, notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in the tables and figures) shall not be considered as requirements of this method.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: The method can be extended to include other ortho-phthalates in a number of polymeric substrates.NOTE 2: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

This specification covers standards for high-strength, low-alloy, hot-rolled and cold-rolled steel sheets and strips cut in lengths or coils for structural and miscellaneous purposes. The material shall come in Types 2 and 4 steels having enhanced atmospheric corrosion resistance. The material shall follow specified carbon, manganese, and sulfur contents. Tension test shall be performed and material shall comply with tensile strength, yield strength, and elongation requirements. Edges and surface finish of the materials shall conform to specifications. Guidelines for retests are also given.1.1 This specification covers high-strength, low-alloy, cold-rolled sheet and strip in cut lengths or coils, hot-rolled sheet and strip steel in cut lengths or coils with ordered thickness less than 0.230 in. [6.0 mm], and hot-rolled sheet coils (not cut lengths) with ordered thickness 0.230 in. [6.0 mm] and thicker, intended for use in structural and miscellaneous purposes, where savings in weight or added durability are important. These steels have enhanced atmospheric corrosion resistance and are supplied in three types or as commercial steel (CS). Type 2 contains 0.20 % minimum copper based on cast or heat analysis (0.18 % minimum Cu for product check). Type 4 and Type 5 contain additional alloying elements and provide a level of corrosion resistance substantially better than that of carbon steels with or without copper addition (Note 1). When properly exposed to the atmosphere, Type 4 and Type 5 steels can be used in the bare (unpainted) condition for many applications. CS is intended for applications that require enhanced atmospheric corrosion resistance which do not require a specified strength. CS shall contain the chemical requirements of Type 2, Type 4, or Type 5. CS as contained within this specification is not associated with the requirements of CS that are referenced in other Subcommittee A01.19 on Steel Sheet and Strip specifications.NOTE 1: For methods of establishing the atmospheric corrosion resistance of low-alloy steels, see Guide G101.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 Welding—In general, the steels listed in this specification are weldable with commonly obtained welding electrodes. When the steel is to be welded, a suitable welding procedure based on its composition should be used, taking into account intended use and service temperatures.NOTE 2: For a general discussion of the weldability of steel and carbon equivalents, consult Appendix X3 of A6/A6M.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification2 covers rod of low-carbon nickel-chromium- molybdenum alloys (UNS N10276, N06022, N06035, N06455, N06058, and N06059), low-carbon nickel-molybdenum- chromium-tantalum (UNS N06210), low-carbon nickel-chromium-molybdenum-copper alloy (UNS N06200), and low-carbon nickel-chromium-molybdenum-tungsten (UNS N06686), for use in general corrosive service. Product and chemical analyses shall be performed on the materials and shall conform to the required chemical composition in molybdenum, chromium, iron, tungsten, cobalt, carbon, silicon, manganese, vanadium, phosphorus, sulfur, titanium, nickel, aluminum, copper, and tantalum. Tension test shall be performed and shall comply to required mechanical properties for hot or cold finished, solution annealed rods such as tensile strength, yield strength, and elongation. 1.1 This specification2 covers rod and bar of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06035, N06044, N06455, N06058, and N06059), low-carbon nickel-molybdenum-chromium (USN N10362), low-carbon nickel-molybdenum-chromium-tantalum (UNS N06210), low-carbon nickel-chromium-molybdenum-copper alloy (UNS N06200), and low-carbon nickel-chromium-molybdenum-tungsten (UNS N06686) as shown in Table 1, for use in general corrosive service. 1.2 The following products are covered under this specification: 1.2.1 Rods and Bars 5/16 in. to 3/4 in. (7.94 mm to 19.05 mm), exclusive, in dimension3, solution annealed and pickled, or mechanically descaled. 1.2.2 Rods and Bars 3/4 in. to 31/2 in. (19.05 mm to 88.9 mm), inclusive, in dimension3, solution annealed, ground or turned. 1.2.3 Rods and Bars 1/4 in. to 3 1/2 in. (6.35 mm to 88.9 mm), inclusive, in dimension3, solution annealed, cold worked, ground or turned (N06022, N06059, N06686, and N10276, see Table 2 and Table 3). 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车