5.1 Glass specimens to be tested shall be mounted in a standard test frame with four sides supported, or in a test frame designed to represent specific glazing conditions.5.2 Loads on glass in windows, curtain walls, and doors may vary greatly in magnitude, direction, and duration. Any design load (wind, snow, etc.) that can reasonably be applied to the test specimens or transformed into an equivalent uniform design load can be considered. Load transformation techniques are addressed in the literature (1, 2, 3).35.3 The strength of glass varies with many different factors including surface condition, load duration, geometry, relative humidity, and temperature (4). A thorough understanding of those strength variations is required to interpret results of this test method.1.1 This proof load test method is a procedure to determine, with a 90 % confidence level, if the probability of breakage under design loads for a given population of glass specimens is less than a selected value. It is not intended to be a design standard for determining the load resistance of glass. Practice E1300 shall be used for this purpose.1.2 This test method describes apparatus and procedures to select and apply a proof load to glass specimens, to determine the number of glass specimens to be tested, and to evaluate statistically the probability of breakage. This test method may be conducted using the standard test frame specified herein or a test frame of the user's design.1.3 Proper use of this test method requires a knowledge of the principles of pressure measurement and an understanding of recommended glazing practices.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

5.1 This test method is a general procedure for testing architectural glass products under uniform static loads.5.2 Loads on glass in windows, curtain walls, and doors may vary greatly in magnitude, direction, and duration. An understanding of wind loads on the building is required for selection of test loads and interpretation of results with respect to expected exposure at a particular site.5.3 A thorough understanding of the variations of the strength of glass and the nature of loading is required to interpret results of this test method.5.4 The proper use of this test method requires a knowledge of the principles of pressure, deflection, and strain measurement.1.1 This test method is a general test procedure for load tests of glass subjected to uniform static loads. It is applicable for test protocols involving specified loads, load durations, and loading rates.1.2 This test method is applicable to architectural flat glass of various types; for example, annealed, heat-strengthened, fully tempered, laminated, insulating, and combinations thereof.1.3 This test method describes a process of applying specific test loads to glass. The test may be conducted using a standard test frame specified herein or a test frame of the user's design.1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements see Section 7.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This guide is intended to provide a standardized method and a set of basic instructions for performing stack testing on UN packaging designs using either guided or unguided top loads. This guide provides the suggested minimum information that should be documented when conducting stacking test and provides information for recommended equipment.4.2 All packaging design types other than bags must be subjected to a stacking test. Packagings subject to the stacking test must be capable of withstanding a superimposed top load of a specified minimum mass for a specified period of time without failure as these parameters are defined in the regulations. The test is not intended to determine the absolute top load capability of a packaging.NOTE 1: When quantification of box compression strength is desired for determining stacking strength or for design purposes use Test Method D642 and conditioning as recommended in 4.5.4.3 Design qualification testing procedures are intended, as explicitly stated in the HMR, to be the minimum performance capability levels for packaging manufactured to transport Hazardous Materials under conditions normally incident to transportation.4.4 The HMR tests are designed to be gross package capability evaluations that can be performed in a similar manner in all parts of the world, but under circumstances with some variance in test facility capabilities. This is an intentional feature of the test designs and protocols. The focus of HMR testing is not the determination of quantifiable, comparison data to allow for analytical evaluation.4.5 It is recommended that facilities performing the HMR tests consult the guidance on conditioning in the relevant ASTM documents for any particular packaging material as applicable. The following conditioning documents, Practices D4332 and D685, are commonly used.1.1 This guide is intended to provide a standardized method and a set of basic instructions for conducting stacking tests on United Nations (UN) non-bulk, intermediate bulk container (IBC), and Large Packagings. Using guided or unguided loads in accordance with the U.S. Department of Transportation Title 49 Code of Federal Regulations (CFR) and the UN Recommendations on the Transport of Dangerous Goods (“The Orange Book”). The combination or interchange of these regulations will be referred to as the Hazardous Material Regulations (HMR).1.2 The Dangerous Goods Regulations require performance tests to be conducted on packaging designs prior to being authorized for use. The regulations do not include standardized procedures to accomplish this which can result in differences between testing facilities. The purpose of this document is to provide guidance and to establish a set of common practices for conducting stack testing on packagings undergoing UN certification.1.3 The user of this guide must be trained in accordance with 49 CFR as required by 172.700 and should be familiar with other applicable hazardous materials regulations such as; International Civil Aviation Organization (ICAO) Technical Instructions for the Safe Transport of Dangerous Goods by Air, the International Maritime Dangerous Goods Code (IMDG Code), and carrier rules such as International Air Transport Association (IATA) Dangerous Goods Regulations.1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车