定价： 819元 / 折扣价： 697 元 加购物车

定价： 819元 / 折扣价： 697 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 605元 / 折扣价： 515 元 加购物车

定价： 936元 / 折扣价： 796 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

4.1 This practice provides one means for determining the aeroplane structural loads for flight, control surfaces, and control systems. This practice satisfies the simplified loads requirements set forth in Specification F3116/F3116M for Normal Category Aeroplanes.1.1 This practice provides an acceptable means of meeting the airworthiness requirements for the flight design loads and conditions of small normal category level 1 and 2 aeroplanes. The material was developed through open consensus of international experts in general aviation. This information was created by focusing on Normal Category aeroplanes. The content may be more broadly applicable; it is the responsibility of the applicant to substantiate broader applicability as a specific means of compliance. The topics covered within this practice are: Simplified Design Load Criteria, Acceptable Methods for Control Surface Loads Calculations, Acceptable Methods for Primary Control System Loads Calculations, and Control Surface Loading (Level 1 Aeroplanes).1.2 This practice is applicable to normal category, low-speed, level 1 and 2 aeroplanes. Use of the term aeroplane used throughout this practice will mean “normal category, low-speed, level 1 or 2 aeroplane,” unless otherwise stated.1.3 An applicant intending to propose this information as means of compliance for a design approval must seek guidance from their respective oversight authority (for example, published guidance from applicable CAAs) concerning the acceptable use and application thereof. For information on which oversight authorities have accepted this standard (in whole or in part) as an acceptable means of compliance to their regulatory requirements (hereinafter “the Rules”), refer to the ASTM Committee F44 web page (www.astm.org/COMMITTEE/F44.htm).1.4 This document may present information in either SI units, English Engineering units, or both. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1.1 This practice provides an acceptable, and simplified, means of determining certain design loads criteria and conditions for fixed wing aircraft. In particular, the practice provides overall aircraft flight loads and flight conditions as well as control surface loads, wing loads, gust load factors, and gust loads on stabilizing surfaces.1.2 This practice is intended to be referenced by other standards that define requirements for comprehensive aircraft loads. This practice does not provide all aircraft loads required for structural compliance. In addition, each load or condition determined through this practice has limitations on its use within the relevant section to which it must adhere.1.3 Units—The values given in this standard are in SI units and are to be regarded as standard. Any values given in parentheses are mathematical conversions to inch-pound (or other) units that are provided for information only and are not considered standard. The values stated in each system may not be exact equivalents. Where it may not be clear, some equations provide the units of the result directly following the equation.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers airworthiness requirements for the design loads and conditions of small airplanes, and is applicable to small airplanes as defined in the F44 terminology standard. The applicant for a design approval must seek individual guidance from their respective civil aviation authority (CAA) body concerning the use of this specification as part of a certification plan.1.1 This specification addresses the airworthiness requirements for the design loads and conditions of small airplanes.1.2 This specification is applicable to small airplanes as defined in the F44 terminology standard. Use of the term airplane is used throughout this specification and will mean “small airplane.”1.3 The applicant for a design approval must seek individual guidance from their respective CAA body concerning the use of this standard as part of a certification plan. For information on which CAA regulatory bodies have accepted this standard (in whole or in part) as a means of compliance to their Small Airplane Airworthiness Rules (hereinafter referred to as “the Rules”), refer to ASTM F44 webpage (www.ASTM.org/COMMITTEE/F44.htm) which includes CAA website links.1.4 Units—Currently there is a mix of SI and Imperial units. In many locations, SI units have been included otherwise units are as they appear in Amendment 62 of 14 CFR Part 23. In a future revision values will be consistently stated in SI units followed by Imperial units in square brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车