4.1 The use of the body measurement information in Table 1 and Table 2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should, in turn, reduce or minimize consumer confusion and dissatisfaction related to apparel sizing (also refer to ISO 3635 Size Designation Procedures).FIG. 1 Form Front View 2-6 Little KidsFIG. 2 Form Quarter View 2-6 Little KidsFIG. 3 Form Side View 2-6 Little KidsFIG. 4 Form Back View 2-6 Little Kids1.1 These tables list body measurements of little kids’ figure type regular sizes 2-6. Although these are body measurements, they can be used as a baseline in designing apparel for little kids in this size range when considering such factors as fabric type, ease for body movement, styling, and fit.1.2 These tables list body measurements for the complete range of little kids regular sizing.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 The use of the body measurement information in Tables 1–2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should in turn reduce or minimize consumer confusion and dissatisfaction related to apparel sizing. (Also refer to ISO 3635 Size Designation Procedures).4.2 Three-dimensional avatars depicting each of the girls’ sizes on certain measures, were created by Alvanon, Inc. and included in this standard to assist manufacturers in visualizing the posture, shape, and proportions generated by the measurements charts in the accompanying Tables. (See Figs. 1–4.)1.1 These tables list body measurements of big girl’s figure Type Regular sizes 7 through 20. Although these are body measurements, they can be used as a baseline in designing apparel for girls in this size range when considering such factors as fabric type ease for body movement, styling, and fit.1.2 These tables list body measurements for the complete range of big girl’s regular sizing.1.3 The values stated in either acceptable SI units or inch units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 The use of the body measurement information in Tables 1–2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should in turn reduce or minimize consumer confusion and dissatisfaction related to apparel sizing. (Also refer to ISO 3635 Size Designation Procedures).4.2 Three-dimensional avatars depicting each of the big boys’ sizes on certain measures, were created by Alvanon, Inc. and included in this standard to assist manufacturers in visualizing the posture, shape, and proportions generated by the measurements charts in the accompanying Tables. (See Figs. 1–4.)1.1 These tables list body measurements of big boy’s regular figure Type sizes 7 through 20. Although these are body measurements, they can be used as a baseline in designing apparel for boys regular in this size range when considering such factors as fabric type ease for body movement, styling, and fit.1.2 These tables list body measurements for the complete range of big boy’s sizing.1.3 The values stated in either acceptable SI units or inch units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 Intervertebral body fusion devices are generally simple geometric-shaped devices, which are often porous or hollow in nature. Their function is to support the anterior column of the spine to facilitate arthrodesis of the motion segment.5.2 This test method is designed to quantify the subsidence characteristics of different designs of intervertebral body fusion devices since this is a potential clinical failure mode. These tests are conducted in vitro in order to simplify the comparison of simulated vertebral body subsidence induced by the intervertebral body fusion devices.5.3 The static axial compressive loads that will be applied to the intervertebral body fusion devices and test blocks will differ from the complex loading seen in vivo, and therefore, the results from this test method may not be used to directly predict in vivo performance. The results, however, can be used to compare the varying degrees of subsidence between different intervertebral body fusion device designs for a given density of simulated bone.5.4 The location within the simulated vertebral bodies and position of the intervertebral body fusion device with respect to the loading axis will be dependent upon the design and manufacturer's recommendation for implant placement.1.1 This test method specifies the materials and methods for the axial compressive subsidence testing of non-biologic intervertebral body fusion devices, spinal implants designed to promote arthrodesis at a given spinal motion segment.1.2 This test method is intended to provide a basis for the mechanical comparison among past, present, and future non-biologic intervertebral body fusion devices. This test method is intended to enable the user to mechanically compare intervertebral body fusion devices and does not purport to provide performance standards for intervertebral body fusion devices.1.3 This test method describes a static test method by specifying a load type and a specific method of applying this load. This test method is designed to allow for the comparative evaluation of intervertebral body fusion devices.1.4 Guidelines are established for measuring test block deformation and determining the subsidence of intervertebral body fusion devices.1.5 Since some intervertebral body fusion devices require the use of additional implants for stabilization, the testing of these types of implants may not be in accordance with the manufacturer's recommended usage.1.6 Units—The values stated in SI units are to be regarded as the standard with the exception of angular measurements, which may be reported in terms of either degrees or radians.1.7 The use of this standard may involve the operation of potentially hazardous equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 Having body armor that fits well and is comfortable begins with appropriate and accurate measurements. Armor suppliers typically have trained representatives that conduct proper measurement and fitting, but not all armor retailers have such trained individuals. This standard will facilitate consistency of measurement across the body armor industry and will help wearers understand proper measurement.1.1 The document provides measurement guidance to assist in fitting ballistic-resistant body armor and stab-resistant body armor covering the torso. Proper measurement is necessary to obtain sufficient coverage of the torso and vital organs while allowing the range of motion required for officer operations.1.2 This document addresses measurements for concealable (normal duty) and tactical (special duty) armor for both male and female wearers.1.3 This standard does not address area of coverage (that is, how much of the torso is covered by the vest).1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7 on Hazards.

定价： 0元 / 折扣价： 0 元

5.1 The purpose of this test method is to provide a measurable criterion of performance about the level of cut resistance provided by different types of protective garments and protected coverings worn by chainsaw operators.5.2 This test method is intended to show to what level a protective garment can offer resistance to the cutting action of a chainsaw.5.3 The protection which can be demonstrated by the garments and coverings tested in accordance with this test method is achieved by: (1) the cut resistance of the material to cutting when put in contact with saw chain; (2) pulling a part of the material or yarns in the material so that they are drawn into the chain and drive mechanism to block the chain movement; (3) the fibers of the materials used to demonstrate both high resistance to cutting and the capacity to absorb rotational energy, so that chain speed can be slowed down sufficiently to stop the movement of the saw chain; or (4) any combination of these.5.4 This test method does not purport to evaluate comfort of lower body protective garments.5.5 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should perform comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens from the same lot of components to be evaluated. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. If a bias is found, either its cause must be determined and corrected or the purchaser and the supplier must agree to interpret future test results in light of the known bias.1.1 This test method measures cut resistance of garments and devices worn to protect the lower body (legs) when operating a chainsaw.1.2 This test method may be used to test for compliance to minimum performance requirements in established safety standards.1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, it will be decided if this test method will be used to determine one or both of the following: (1) chain speed 50 (CS50), and (2) success/failure (jamming/chain stop or no cut in less than 1.5 s) at specified chain speed.1.3 This test method may be used to determine levels of protection for areas of coverage as stipulated in established safety standards.1.4 The values stated in SI units are to be regarded as standard.NOTE 1: The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

4.1 This guide is intended for use by law enforcement, corrections, or other public safety agencies in planning and managing a body armor program. The overarching objective is officer safety and assisting with risk management.4.2 This guide was developed via a collaborative partnership between local, state, and federal public safety agencies, body armor wearers, vendors, fitters, and unions (for example, Fraternal Order of Police). The purpose is to guide law enforcement, corrections, or other public safety agencies in planning and managing a body armor program.4.3 A graphical overview showing all aspects and interrelated activities of planning and managing a body armor program is provided in Appendix X1 of this guide.1.1 The purpose of this guide is to assist law enforcement, corrections, or other public safety agencies in planning and managing a body armor program.1.2 This guide addresses ballistic-resistant, stab-resistant, multi-threat, combination, concealable soft, hard plate, and tactical body armor.1.3 This guide specifically includes the National Institute of Justice (NIJ) body armor program as a provider of performance standards, guidance, and certification for body armor. While many countries recognize the NIJ body armor program, applicable certification programs of other countries should be consulted.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 The use of the body measurement information in Tables 1 and 2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should in turn reduce or minimize consumer confusion and dissatisfaction related to apparel sizing. (Also refer to ISO 3635 Size Designation Procedures.)1.1 These tables list body measurements of young adult female junior figure type, sizes 0 to 19. Although these are body measurements, they can be used as a baseline in designing apparel for young women in this size range when considering such factors as fabric type, ease for body movement, styling, and fit.1.2 The junior body is younger, not fully developed, with a higher waistline than other women's size ranges.1.3 The values stated in either acceptable SI units or inch-pound units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

4.1 The use of the body measurement information in Tables 1 and 2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should, in turn, reduce or minimize consumer confusion and dissatisfaction related to apparel sizing. (Also refer to ISO 3635.)4.2 Three-dimensional avatars depicting each of the big men sizes on certain measurements were created by Alvanon, Inc. and included in these tables to assist manufacturers in visualizing the posture, shape, and proportions generated by the measurements charts in Figs. 1-3.FIG. 1 Mature Big MenFIG. 2 Mature Big MenFIG. 3 Mature Big Men1.1 These tables list body measurements of mature big men figure type sizes 46–64. Although these are body measurements, they can be used as a baseline in designing apparel for big men in this size range when considering such factors as fabric type ease for body movement, styling, and fit.1.2 These tables list body measurements for the complete range of big men sizing.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 The use of the body measurement information in Tables 1-4 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should, in turn, reduce or minimize consumer confusion and dissatisfaction related to apparel sizing. (Also refer to ISO 3635 Size Designation Procedures.)4.2 Three-dimensional avatars depicting each of the children’s sizes were created by Alvanon, Inc. and included in this standard to assist manufactures in visualizing the posture, shape, and proportions generated by the measurement charts in the accompanying tables. (See Figs. 1-9.)FIG. 1 Form Front 2–6FIG. 2 Form Side 2–6FIG. 3 Form Back 2–6FIG. 4 Form Front 7–20 Reg. BoysFIG. 5 Form Side 7–20 Reg. BoysFIG. 6 Form Back 7–20 Reg. BoysFIG. 7 Form Front 4–20 Slim BoysFIG. 8 Form Side 4–20 Slim BoysFIG. 9 Form Back 4–20 Slim Boys1.1 These tables list body measurements of boys sizes. Although these are body measurements, they can be used as a baseline in designing apparel for boys in this size range when considering such factors as fabric type, ease for body movement, styling, and fit.1.2 The maximum age for the Boy’s chart is 15 years old to the size 20.1.3 The size table includes the range of toddler sizes; these values are for both girls and boys and will be included in the girl’s standard as well.1.4 These tables list body measurements for the complete range of Boys sizing. (Regular, Slim) Slim subjects are of same stature (height), with a slimmer body, and lower body weight than regular subjects as illustrated by the measurement charts.1.5 The values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

4.1 U.S. Department of Defense and U.S. Department of Justice standards for assessing the performance of ballistic-resistant torso body armor require the use of backing assemblies made with Roma Plastilina No. 1®. The creation of appliques behind nonplanar soft armor test items must be done in a consistent manner to reduce variability within and between laboratories.4.2 This practice is applicable for certification testing or for research and development testing.1.1 This practice specifies a procedure for creating appliques (that is, build-up of clay) for use behind nonplanar, soft body armor test items and affixing the appliques to the clay block.NOTE 1: This practice describes a single applique shape; additional shapes may be described in other standards.1.2 The purpose of this practice is to specify critical parameters for creating appliques in order to improve consistency of the test setup between laboratories.NOTE 2: In the past, testing of nonplanar soft armor has been done either with an unspecified buildup of clay behind the test item or with the test item pressed flat against the clay block.1.3 This practice is applicable only to nonplanar soft body armor designed for females.1.4 This practice is not applicable to hard armor test items.1.5 This practice is primarily directed toward test laboratories but may be applicable to body armor manufacturers, researchers, and end users performing ballistic-resistance testing of body armor.1.6 In this practice, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of this practice. Purchasers and other users are responsible for the “other standards and specifications” and for specifying any requirements that supersede those of this practice.1.7 Units—The values stated in SI units are to be regarded as standard. Where appropriate, inch-pound units are included parenthetically for information purposes.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 The use of the body measurement information in Tables 1 and 2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should, in turn, reduce or minimize consumer confusion and dissatisfaction related to apparel sizing. (Also refer to ISO 3635 Size Designation Procedures.)4.2 Three-dimensional avatars depicting each of the children’s sizes were created by Alvanon, Inc. and included in this standard to assist manufacturers in visualizing the posture, shape, and proportions generated by the measurement charts in the accompanying Tables. (See Figs. 1–8.)1.1 These tables list body measurements of infants’ sizes. Although these are body measurements, they can be used as a baseline in designing apparel for infants in this size range when considering such factors as fabric type, ease for body movement, styling, and fit.1.2 These tables list body measurements for the complete range of infant sizing for boys and girls.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system must be used independently of the other, without combining values in any way.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This test method covers a comparative measurement method for impact absorption properties for body padding and protective wear (apparel) for the sport of fencing. The apparel includes fencing mask bibs, underarm protectors or plastrons, padded vests, uniform jackets, knickers or trousers, gloves, and other protection worn to protect against impacts from the fencing weapon's tip (for example, touches) for foil, saber, or epee. The scope of this test method excludes measurement or performance for perforation resistance of the blade, whether in tact or broken. Note 1-This is a simple test method to discriminate between qualities of different padding materials or systems under an impact that simulates the delivery of a fencing touch. It does not purport to measure quantitative impact energy absorption values at thrust sites. Until in-field data become available, this standard allows manufacturers to intercompare padding systems, fabrics, materials, or composites for protective fencing wear for integrity, robustness, and impact attenuation. 1.2 This standard does not purport to address all of the safety problems associated with fencing padding and will not prevent all injuries due to blades impacting fencers. It is the responsibility of the users of the protective padding to establish appropriate safety practices, including maintaining safe fencing distances and care and inspection of the protective wear as well as the blade. Specifically, this standard does not address degradation of the protective padding with use and laundering, or performance of the padding for puncture resistance by thrusts involving in-tact or broken blades. It should be recalled that the sport derives from duelling and is inherently not free of risk of injury or death .

定价： 0元 / 折扣价： 0 元

5.1 U.S. Department of Defense and U.S. Department of Justice standards and specifications require assessing the penetration resistance and backface deformation of ballistic-resistant body armor.5.2 This test method may be used by private-sector and government laboratories, manufacturers, research and development organizations, and others assessing the ballistic resistance of body armor or performing research and development of new materials.5.3 It is intended that this test method be referenced by other standards, specifications, or test methods.1.1 This test method addresses resistance to ballistic penetration and to backface deformation (BFD) for ballistic-resistant torso body armor and shoot packs.1.2 This test method is intended for testing of soft body armor, hard armor plates, in conjunction with armor, and shoot packs mounted on a clay block as the backing assembly.NOTE 1: This test method does not apply to ballistic helmets, inserts, trauma packs, trauma plates, or accessories.1.3 The test method does not specify performance criteria or usage of the test results.1.4 This test method does not address conditioning of test items.1.5 It is anticipated that this test method will be referenced by certifiers, purchasers, or other users in order to meet their specific needs.1.5.1 Purchasers and other users will specify the ballistic test threats to be used. Within this test method, the reference defining the ballistic test threats is called the “test threats document.”1.5.2 In this test method, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of this test method. Purchasers and other users are responsible for the “other standards and specifications” and for specifying any requirements that supersede those of this test method.1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.6.1 The user of this standard will identify the system of units to be used, and it is critical to ensure that any cross-referenced standards maintain consistency of units between standards.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 The use of the body measurement information in Tables 1 and 2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should in turn reduce or minimize consumer confusion and dissatisfaction related to apparel sizing. (Also refer to ISO 3635 Size Designation Procedures.)4.2 Three-dimensional avatars depicting each of the Misses Petite sizes and sub categories Curvy and Straight on certain measures were created by Alvanon, Inc. and included in this standard to assist manufacturers in visualizing the posture, shape, and proportions generated by the measurements charts in the accompanying Tables5 (Avatar 1-6) (see Figs. 1 and 2).FIG. 1 Missy Petite Avatar CurvyFIG. 2 Missy Petite Avatar Straight1.1 These tables list body measurements of adult female misses petite figure type sizes 00P through 20P. Although these are body measurements, they can be used as a baseline in designing apparel for Misses Petite in this size range when considering such factors as fabric type, ease for body movement, styling, and fit.1.2 These tables list body measurements for the complete range of misses petite sizing.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车