This specification establishes the requirements for flat copper wire and strip products, with rolled or drawn finished edges produced for general applications. Unless otherwise established by agreement between the manufacturer and purchaser, products shall be produced in UNS Copper Nos. C10100, C10200, C10300, C10500, C10700, C10800, C11000, C11040, C12200, and C14200. The material for manufacture shall be a billet, cake, wire bar, or rod suitable for processing by hot working, cold working, and annealing to produce a uniform wrought structure in the finished product. Products shall be produced in the annealed (O61) and cold worked (H00, H01, H02, H03, H04, H06, and H08) tempers. Products shall be tested and shall adhere to dimensional (thickness, width, length, straightness, and edge contour), mechanical (tensile strength, elongation, Rockwell hardness, bend angle, and hydrogen embrittlement susceptibility), electrical resisitvity, and chemical composition requirements.1.1 This specification establishes the requirements for copper products, flat wire and strip, with rolled or drawn finished edges produced for general application.1.1.1 The product is produced in UNS Copper Nos. C10100, C10200, C10300, C10500, C10700, C10800, C11000, C11040, C12200, and C14200 unless otherwise established by agreement between manufacturer and purchaser.1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.NOTE 1: When a copper other than that listed in 1.1.1 is designated by the purchaser, the resulting product shall conform to the physical, mechanical, performance, dimensional, and tolerance requirements per agreement between the manufacturer and purchaser.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the requirements for wrought seamless and welded and drawn cobalt alloy small diameter tubing used for the manufacture of surgical implants. Product variables that differentiate small diameter medical tubing from the bar, wire, sheet, and strip product forms are addressed. This specification applies to straight length tubing of specified diameters and thickness. Seamless tubing shall be made from bar, hollow bar, rod, or hollow rod raw material forms through a prescribed process. Welded and drawn tubing shall be made from strip or sheet raw material forms that meet the specified chemical requirements. The tubing shall be subject to tensile testing.1.1 This specification covers the requirements for wrought seamless and welded and drawn cobalt alloy small diameter tubing used for the manufacture of surgical implants. Material shall conform to the applicable requirements of Specifications F90, F562, F688, F1058 or F1537, Alloy 1. This specification addresses those product variables that differentiate small diameter medical tubing from the bar, wire, sheet, and strip product forms covered in these specifications.1.2 This specification applies to straight length tubing with 6.3 mm [0.250 in.] and smaller nominal outside diameter (OD) and 0.76 mm [0.030 in.] and thinner nominal wall thickness.1.3 The specifications in 2.1 are referred to as the ASTM material standard(s) in this specification.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 605元 / 折扣价： 515 元

定价： 345元 / 折扣价： 294 元

This specification covers cold-drawn, stress-relieved carbon steel bars subject to mechanical property requirements. The bars are furnished in two classes, A and B. Class A are normal-draft cold-drawn and stress-relieved rounds, squares, hexagons, and flats. Class B are heavy-draft cold-drawn and stress-relieved rounds and hexagons. The steel shall be made by one or more of the following primary processes: open-hearth, basic-oxygen, or electric-furnace. The cast or heat analysis shall conform to the chemical composition requirements specified. Tension test shall be made to conform to the requirements specified.1.1 This specification covers two classes, nine grades, and four conditions of stress-relieved cold-drawn carbon steel bars produced to mechanical property requirements. One class, B, is cold drawn with higher than normal (heavy) drafts to provide higher strength levels, and four grades provide improved machinability.1.2 Supplementary Requirements, S1 through S6, of an optional nature are provided.1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers annealed, drawn or rolled iron-chromium-aluminum alloy shapes used for electrical heating and resistance purposes. This specification contains the requirements for chemical composition, electrical resistance, mechanical properties and temperature-dependent changes in resistance of the alloys.1.1 This specification covers annealed, drawn, or rolled shapes for electrical heating and resistance purposes of alloys consisting mainly of iron, chromium, and aluminum as detailed in Table 1.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers two classes of uncoated, high-strength, hard-drawn steel wires for use in the manufacture of prestressed concrete pipe. The steel shall be made by the open-hearth, basic-oxygen, or electric-furnace process, and shall be free of injurious piping and undue segregation. The wire shall be cold drawn to produce the desired mechanical properties and there shall be no welds or joints in the finished wire. Cast or heat analysis of the steel shall conform to the chemical requirements specified for carbon, manganese, phosphorus, sulfur, silicon, and nitrogen. The tension and relaxation tests shall conform to the specified tensile requirements including tensile strength and breaking strength. Torsion test shall also be performed where test specimens shall be inspected for primary break shear area and longitudinal (spiral) splitting following completion of the test.1.1 This specification covers two classes of uncoated, high-strength, hard-drawn steel wire for use in the manufacture of prestressed concrete pipe. In application, the wire is helically wrapped on the pipe maintaining tension by mechanical means not including drawing dies.1.2 A supplementary requirement (S1) is provided for use where hydrogen embrittlement (HE) resistance testing is required by the purchaser. Supplementary requirement (S1), which establishes acceptance criteria for HE resistance testing, applies only when specified in the purchase order or contract.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 The following caveat pertains only to the test method portions of this specification, 6.3.3 and 6.5.3: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers round, uncoated, high tensile strength, cold-drawn steel spring wires having properties and quality suitable for the manufacture of mechanical springs and wire forms subject to high static stresses or infrequent dynamic load, or both. The steel shall be made by any commercially accepted steel making process. The steel shall either be ingot cast or continuous strand cast. The finished wire shall be free from detrimental pipe and undue segregation. The wire shall be cold drawn to produce the desired tensile strength. The wire finish shall be suitable for forming or coiling. It is not intended that this material be furnished with a metallic coating. Heat and product analysis shall be conducted wherein the material shall conform to the required chemical composition values of carbon, manganese, phosphorus, sulfur, and silicon. The material shall undergo tensile and wrap tests. The steel shall have fine pearlite microstructure and the wire surface shall not exhibit imperfections.1.1 This specification covers round, uncoated, high tensile strength, cold drawn steel spring wire, having properties and quality suitable for the manufacture of mechanical springs and wire forms subject to high static stresses or infrequent dynamic load, or both.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This specification establishes the requirements for hard-drawn, seamless capillary tube made from Copper Alloy UNS Nos. C10800, C12000, or C12200.1.2 This tube is commonly supplied in straight lengths intended for restrictor applications such as metering lines for liquids and gases where close control over smoothness and diameter of the bore is required to insure uniform flow characteristics between tubes.1.3 Units—The values stated in inch pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification covers round, cold-drawn, steel spring wire having properties and quality intended for the manufacture of the following types of upholstery springs:1.1.1 Type A—Coiled (Marshall pack),1.1.2 Type B—Coiled and knotted,1.1.3 Type C—Coiled and knotted (offset style),1.1.4 Type D—Coiled and hooked (single and cross helicals),1.1.5 Type E—Coiled and hooked (short tension—regular tensile strength),1.1.6 Type F—Coiled and hooked (short tension—high tensile strength),1.1.7 Type G—Regular lacing,1.1.8 Type H—Automatic lacing,1.1.9 Type I—Zig-zag (U-formed),1.1.10 Type J—Square-formed, and1.1.11 Type K—Sinuous for furniture spring units.1.2 These types of upholstery springs are used in the manufacture of automotive seat springs, furniture springs, bed spring units, mattresses, furniture cushions, and automobile seats. This wire is not intended for the manufacture of mechanical springs.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 Hard-drawn steel wire as used in prestressed concrete pipe may be exposed to elemental hydrogen favorable to hydrogen induced embrittlement and cracking. Resistance to hydrogen embrittlement is necessary for prestressing wire to provide long-term performance to installed pipe.4.2 The length of time that a stressed wire specimen resists failure while exposed to a heated solution of NH4SCN, is an indication of the specimen's resistance to hydrogen embrittlement.1.1 This test method describes procedures to determine the hydrogen embrittlement (HE) resistance of hard-drawn steel wire used for prestressed concrete pipe.1.2 HE resistance is reported as time-to-failure of specimens tested in a laboratory.1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers round, uncoated, cold-drawn spring wire in coils intended for the manufacture of upholstery springs such as zig-zag, square-formed, and sinuous. The steel shall be made by open-heart, basic-oxygen, or electric-furnace processes. Heat analysis shall be made to determine the percentage of elements, such as carbon and manganese, present in the spring wire. Tension and wrap tests shall be done for one test specimen for each ten coils. Workmanship, inspection, packaging, product marking, and loading are also covered.1.1 This specification covers round, uncoated, cold-drawn spring wire in coils having properties and quality intended for the manufacture of the following upholstery springs:1.1.1 Type A—Zig-zag (U-formed),1.1.2 Type B—Square-formed, and1.1.3 Type C—Sinuous for furniture spring units.1.2 These types of upholstery springs are used in the manufacture of automotive seat springs and furniture springs. The wire is not intended for the manufacture of mechanical springs.

定价： 0元 / 折扣价： 0 元

This specification covers four conductivities of bare, hard-drawn, round, aluminum-clad steel wire for general use for electrical purposes. The wire shall be composed of a steel core with a substantially uniform and continuous aluminum covering thoroughly bonded to it. The drawn wire shall have the properties and characteristics prescribed in the specification. The wire of varying nominal diameters shall conform to the prescribed tensile requirements such as tensile strength and elongation. The electrical resistance of the wire shall be determined by resistance measurements and maximum resistance shall be based on the nominal diameter of the wire and the resistivity value. The steel wire shall conform to the prescribed values of physical constants such as modulus of elasticity, coefficient of linear expansion, and temperature coefficient of resistance. Within a required range of diameters, the wire shall not vary from the specified diameter by more than the amount indicated. The aluminum thickness at any point shall not be less than the required values. The wire shall undergo a twist test, where the specimen shall be gripped at its ends in vises, one of which shall be free to move longitudinally during the test. The finished wire shall contain no joints or splices. The material shall also conform to the approximate properties of hard-drawn conductivity aluminum-clad steel wire.1.1 This specification covers four conductivities of bare, hard-drawn, round, aluminum-clad steel wire for general use for electrical purposes in sizes 0.2043 to 0.0808 in. incl (4 to 12 AWG) (Note 1). This specification does not apply to wires used as reinforcement in ACSR conductors. (See Specification B502.)NOTE 1: Wire ordered to this specification is not intended for redrawing. If wire is desired for this purpose, the manufacturer shall be consulted.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers hard-drawn round copper alloy wires for electric conductors. The wires shall be made in any one of ten distinct alloys designated 8.5, 13, 15, 20, 30, 40, 55, 74, 80, and 85 in accordance with their increasing electrical conductivities. Specimens shall undergo tests to which they shall meet the required values for chemical composition, electrical resistivity, and mechanical and physical properties. The mechanical properties to be examined are elongation and tensile strength, while the physical properties in consideration are wire diameter, area, and density. The completed wire, to which no joints are to be made, shall be free from all imperfections not consistent with the best commercial practice.1.1 This specification covers hard-drawn round copper alloy wires for electric conductors.1.2 The copper alloy wires shall be made in any one of ten distinct alloys designated 8.5 to 85 in accordance with their increasing conductivities or designated by assigned UNS numbers (see Explanatory Note 1) as follows:  Copper Alloy UNSNo.   Copper Alloy UNSNo. Alloy 8.5 C65100 Alloy 40  Alloy 13 C51000 Alloy 55 C16500Alloy 15   Alloy 74 C19600Alloy 20   Alloy 80 C16200Alloy 30 C50700 Alloy 85 C162001.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3.1 Exception—The SI values of density and resistivity are to be regarded as standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 0元 / 折扣价： 0 元

1.1 This specification covers annealed, drawn, or rolled shapes for electrical heating purposes, of alloys having the nominal compositions of 80 % nickel and 20 % chromium; 60 % nickel, 16 % chromium, and remainder iron; and 35 % nickel, 20 % chromium, and remainder iron; 38 % nickel, 21 % chromium, and remainder iron; and 35 % nickel, 20 % chromium remainder iron.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车