定价： 481元 / 折扣价： 409 元

定价： 689元 / 折扣价： 586 元

定价： 0元 / 折扣价： 0 元 加购物车

This specification covers leather protectors for rubber insulating gloves and mittens. Leather protectors shall provide mechanical protection only for the rubber insulating gloves and mittens. Leather material shall be grain cowhide, buffled gain cowhide, grain deerskin, grain pigskin, grain horsehide, or grain goatskin. Leather protectors shall be manufactured in clute, gunn, montpelier, or one-finger mitten patterns. Stiching, dimensions, workmanship, and markings shall conform to the requirements of this specification.1.1 This specification covers leather protector gloves and leather protector mittens to be worn over electrical workers' rubber insulating gloves and rubber insulating mittens.1.2 It is intended that the gloves specified herein shall fit snugly and without undue wrinkles over rubber insulating gloves and rubber insulating mittens specified in Specification D120.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 Intra-oral mouth protectors have been found usable and effective in all physical sports activities where mouth hazard exists.4.2 Considerable evidence indicates that the use of mouth protectors reduces forces on dentition and can potentially mitigate orofacial injuries.1.1 This practice covers the care and use of intraoral mouth protectors as protective equipment for sports. Mouth protectors includes what are commonly termed mouth guards.1.2 Mouth protectors, as described herein, refer to either Type I, Type II, or Type III mouth protectors as classified in Section 3.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This specification covers eye protectors designed for use by players of handball that minimize or significantly reduce injury to the eye and adnexa due to impact and penetration of balls. Protective eyewear offers protection only to the eyes and does not protect other parts of the head.1.2 Impact testing is done in a laboratory setting. Eye contact is determined by observation.1.3 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

This specification covers the design and minimum performance criteria, and associated test methods (including apparatuses required for) for body protectors used in horse sports and horseback riding. The body protectors shall meet specified requirements for the material used, protector assembly, extent and form of protective material, attachments, and dimension, sizing, and body coverage. The testing procedures that the body protectors shall go through are shock attenuation test, penetration and deformation test, impact sites test, padding separation test, and closure test. Prior to testing, each body protector should be conditioned in accordance to ambient temperature, low temperature, high temperature, and water immersion.1.1 This specification covers minimum performance criteria and describes test methods for body protectors for use in horse sports and horseback riding.1.2 It is not the intention of this specification to bar from consideration materials of improved quality or performance not known at the time of development of this specification.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification covers eye protectors, designed for use by players of racket sports (racquetball, squash, tennis), that minimize or significantly reduce injury to the eye and adnexa due to impact and penetration by racket-sport rackets and balls. Protective eyewear offers protection only to the eyes and does not protect other parts of the head.1.2 Protectors are divided into three types depending on their design characteristics.1.3 This specification applies to eye protectors for use by wearers of corrective lenses and also by those players who do not require prescription eyewear. (Warning—Polycarbonate or Trivex spectacle lenses should be used if spectacles are worn under protective eyewear.)1.4 In this standard, the use of the words “shall” or “must” indicates a mandatory requirement. The word “should” indicates a recommendation.1.5 Failure of the product occurs when the protector is unable to meet the general, mechanical, and optical (if applicable) requirements of the standard.1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate.1.7 The following precautionary caveat pertains only to the test methods portions, Sections 9 – 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 819元 / 折扣价： 697 元

定价： 689元 / 折扣价： 586 元

This specification covers eye protectors, designed for use by players of field hockey that minimize or significantly reduce injury to the eye and adnexa due to impact by and penetration of field hockey balls and field hockey sticks. Contact with the eye of the headform constitutes failure. Protective eyewear offers protection only to the eyes and does not protect other parts of the head. Eye protectors are classified into the following types: Types I, II, and III. Optical quality, luminous transmittance, prismatic deviation measurements, haze, refractive power measurements, surface imperfections and internal defects, and mechanical tests shall be performed to conform to the specified requirements.1.1 This specification covers eye protectors with a plano or prescription lens or without a lens, designed for use by players of field hockey, that minimize or significantly reduce injury to the eye and adnexa due to impact by and penetration of field hockey balls and field hockey sticks. Contact with the eye of the headform constitutes failure. Protective eyewear offers protection only to the eyes and does not protect other parts of the head.1.2 Testing is done in a laboratory setting. Eye contact is determined by observation.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate.1.4 The following precautionary caveat pertains only to the test methods portion (Sections 8, 9, and 10) of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers eye protectors, designed for use by players of racket sports, women's lacrosse, field hockey, basketball, baseball, and soccer that minimize or significantly reduce injury to the eye and adnexa due to impact and penetration by racket-sport rackets and balls, women's lacrosse and field hockey sticks and balls, baseballs, soccer balls, hands, elbows, and fingers. Protective eyewear offers protection only to the eyes and does not protect other parts of the head. Protectors are divided into four types depending on their design characteristics as follows: Type I—A protector with the lens or lenses and frame frontpiece molded as one unit. Frame temples or other devices, such as straps, to affix the lens/frontpiece may be separate pieces; Type II—A protector with a single lens or lenses, either plano or prescription, mounted in a frame that was manufactured as a separate unit; Type III—A protector without a lens; and Type IV—A full or partial face shield. Materials shall be tested using optical tests such as field of view, optical quality, luminous transmittance, prismatic deviation measurements, haze, refractive power measurements, surface imperfections and internal defects, and alternate optical tests; and mechanical tests such as high velocity impact resistance, and projectile simulator test. In addition, the individual grades shall conform to the general, and performance requirements.1.1 This specification covers eye protectors, designed for use by players of basketball, baseball, and soccer to minimize or significantly reduce injury to the eye and adnexa due to impact and penetration by baseballs and softballs, basketballs, soccer balls, hands, elbows, and fingers. Protective eyewear offers protection only to the eyes and adnexa and does not protect other parts of the head.1.2 Protectors are divided into three types depending on their design characteristics.1.3 This specification applies to eye protectors for use by wearers of corrective lenses and also by those players who do not require prescription eyewear. (Warning—Polycarbonate or Trivex spectacle lenses should be used if spectacles are worn under protective eyewear.)1.4 In this standard, the use of the words “shall” or “must” indicates a mandatory requirement. The word “should” indicates a recommendation.1.5 Failure of the product occurs when the protector is unable to meet the general, mechanical, and optical (if applicable) requirements of the standard.1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate.1.7 The following precautionary caveat pertains only to the test methods portions, Sections 9 – 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1.1 This specification covers minimum performance criteria and describes test methods for body protectors for use in equine racing in a controlled environment.NOTE 1: It is recognized that it is not possible to write a body protector performance standard that will result in products that can protect against all types of injury or death in an accident.1.2 It is not the intention of this specification to bar from consideration materials of improved quality or performance not known at time of development of this specification.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification establishes specifications and test requirements for protectors to be worn over electrical workers’ rubber insulating gloves.1.2 It is intended that the protectors specified herein fit snugly over rubber insulating gloves specified in Specification D120 without causing mechanical damage to the rubber insulating glove. Cinching at the wrist is allowed.1.3 This specification covers the use of a material or combination of materials which do not compromise the integrity of the rubber insulating glove.1.4 Specification F696 was used to establish minimums for this specification.1.5 Protectors meeting this specification do not provide any electrical shock protection if used on their own.1.6 This specification specifies the response of protectors to electric arc, puncture and cut under controlled conditions.1.6.1 Field conditions will not directly correlate to testing methods.1.7 The values stated in SI units are to be regarded as the standard except as noted. See IEEE/ASTM SI-10.1.8 The following safety hazards caveat pertains only to the test method portion, Sections 6 and 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车