This specification establishes recognized requirements for determining the child resistance of portable gasoline containers intended for use by consumers. The following tests shall be performed: senior adult test; child-resistant test (test subject/selection criteria); child-resistant tests (test failures); sequential test; and senior adult use effectiveness to conform with the specified requirements.1.1 This specification establishes recognized requirements for determining the child resistance of portable fuel containers (PFCs) and other types of portable containers intended for use by consumers to hold, store, and transport liquid fuels such as gasoline, kerosene, and diesel.1.1.1 “Portable Fuel Container” is defined in Specification F852 and includes the receptacle for gasoline, kerosene, or diesel fuel as well as spouts, caps, and other closure mechanisms and components for use with or on portable gasoline, kerosene, or diesel receptacles.1.1.2 This specification is also applicable to spouts, caps, or other closure mechanisms sold separately for use with or on a fuel container.1.1.3 This specification does not cover one-time use portable emergency fuel containers conforming to Specification F2874.1.2 This standard addresses the effectiveness of the child resistance (CR) device only after closure cycling, but does not address closure effectiveness:1.2.1 When at high or low temperatures,1.2.2 After thermal aging of polymers,1.2.3 After exposure to sunlight,1.2.4 After exposure to intended fuels, and1.2.5 After physical abuses, such as drops or impacts.NOTE 1: Please see Appendix X2 for additional information on these exemptions.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This practice outlines lead hazard reduction methods that have been shown to be effective in preventing lead poisoning in children.4.2 This practice tabulates advantages, disadvantages, and relative costs of the reduction methods to assist professionals such as certified lead-based paint risk assessors, supervisors, or project designers in selecting appropriate cost-effective options for controlling lead hazards identified during a lead risk assessment. Different control methods may be equally effective in controlling a given lead hazard and, consequently, the selection of a specific control method may depend on the needs and economic constraints of the client or building owner.4.3 This practice is intended to complement other lead hazard activities that are performed in accordance with regulations promulgated by authorities having jurisdiction. For example, in some jurisdictions, a lead hazard risk assessment, by regulation, consists of a visual assessment, a hazard assessment including environmental monitoring for lead, and selection of lead hazard reduction methods.4.4 This practice is intended to assist homeowners, owners and occupants of rental property, lenders, insurers, and others who have interest in selecting options for controlling lead hazards associated with leaded paint, dust, or soil.4.5 This practice complements Guide E2115. Information and data gathered in accordance with Guide E2115 and this practice are used in preparing a risk assessment report. Subsequent lead hazards are mitigated through implementation of controls selected in accordance with this present practice.4.6 This practice addresses the most commonly used lead hazard reduction methods. It is left to users of this practice to identify the advantages, disadvantages, and relative costs associated with emerging control technologies for comparison with these characteristics of established lead hazard control methods.4.7 This practice does not address specific historic preservation requirements. The interim control and abatement methods in this practice will work in any structure; however, historic preservation regulations promulgated by authorities having jurisdiction may impose specific interim control or abatement methods.1.1 This practice describes the selection of lead hazard reduction methods for controlling lead hazard risks identified during risk assessments of residential dwellings and child occupied facilities.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.1.3 This practice contains notes, which are explanatory and are not part of the mandatory requirements of this standard.1.4 Methods described in this practice may not meet or be allowed by requirements or regulations established by local authorities having jurisdiction. It is the responsibility of the user of this standard to comply with all such requirements and regulations.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 This test method allows for the measurement of the torque retention properties of container/continuous thread closure systems of various designs, materials, and manufacture, and is suitable for package development and engineering evaluation.5.2 Each test method can be used for the evaluation of non child resistant container/continuous thread closure systems under controlled conditions such as when the application torque is known and the applied downward force to the closure is zero or for Type I, style “A” push down and turn child resistant container/continuous thread closure systems under controlled conditions such as when the application torque and the applied downward force to the closure is known.5.3 This test method measures torque retention properties of container/continuous thread closure systems with the use of an automated transducer based torque meter operating at a known rotational velocity (rpm) or known torque ramp.5.4 This test method is intended for measurement of dry torque only.1.1 These test methods evaluate the torque retention of continuous thread closures on containers with matching finishes, for predetermined environmental conditions over time. Methods are defined for both Type I, style “A” push down and turn Type II2 child resistant and non child resistant type closures.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.NOTE 1: The SI unit system is the recommended system.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This consumer safety specification is intended to address incidents reported by the U.S. Consumer Product Safety Commission (CPSC) relating to frame child carriers. In response to the incident data compiled by the CPSC, this consumer safety specification attempts to minimize the hazards associated with these products from the following: occupant retention, structural integrity, and deficiency of consumer education regarding product use. This consumer safety specification is intended to deal with reasonably foreseeable use and misuse of the products. Performance requirements of the frame child carriers shall be determined by subjecting them to the following tests: leg opening test, dynamic strength test, static load test, stability test, locking device test, unintentional folding test, and removal of protective components test such as torque test and tension test. Instructions shall be provided with the product and shall be easy to read and understand. Instructions for assembly, use, maintenance, and cleaning of the product, and warnings, where applicable, shall be included.1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of frame child carriers.1.2 This consumer safety specification is intended to minimize the risk of injury to a child from the normal use and reasonably foreseeable misuse of these products.1.3 For the purposes of this consumer safety specification, a frame child carrier is a product, normally of sewn fabric construction on a tubular metal or other frame, which is designed to carry a child, in an upright position, on the back of the caregiver. A frame child carrier is intended for use with a child that is able to sit upright unassisted and weighs between 16 lb and 50 lb (7.3 kg and 22.7 kg). The frame child carrier is intended to be worn on the back of the caregiver’s body, with the carrier, and thus the child, suspended from both shoulders of the caregiver. The seated position of the child is either facing towards or away from the caregiver.1.4 No frame child carrier produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with the specification unless it complies with all of the requirements contained herein.1.5 This consumer safety specification is not intended to address incidents and injuries resulting from the interaction of other persons or objects with the caregiver and child while the frame child carrier is in use.1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.7 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1.1 This specification covers safety requirements, test methods, and warnings for child safety locks and latches intended to be installed by consumers to the interior of residential cabinet doors or drawers to restrict access to household cabinets by children under the age of 48 months.1.2 Child safety locks and latches that are not covered under this specification include devices:1.2.1 Installed on the exterior of a cabinet door or drawer,1.2.2 Requiring installation by professionals, or1.2.3 That are an integral part of the cabinet door or drawer system.1.3 This specification does not cover child safety locks, latches, and straps intended for use on furniture or appliances as anchoring devices to prevent tip over.1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This guide is intended to help prevent lead poisoning of children by providing standardized procedures for conducting a lead hazard assessment and providing information needed to develop and recommend lead hazard control options as described in Practice E2252.5.2 This guide is applicable for use in either occupied or unoccupied dwellings and in other child-occupied facilities.5.3 The procedures in this guide, when supplemented by recommendations for controlling lead hazards, provide for the conduct of a lead risk assessment of a dwelling or of other child-occupied facilities.5.4 This guide may be used to supplement assessment procedures used to determine the causes of elevated blood lead (EBL) levels in young children.NOTE 2: In cases of EBL levels, investigation of the total living environment of the child and a pediatric medical evaluation may also be needed. Reference should be made to documents such as Managing Elevated Blood Lead Levels Among Young Children,6 Preventing Lead Poisoning in Young Children (1991),7 the HUD Guidelines, and Screening Young Children for Lead Poisoning (1997).75.5 Although this guide was developed for dwellings and for other child-occupied facilities, this guide may be suitable for lead hazard assessments in non-residential buildings and other properties following agreement between assessor and client on appropriate lead action levels.5.6 This guide is not intended for use in identifying building materials that when abraded or otherwise degraded, such as that which may occur in remodeling or renovation activities, may result in lead hazards.5.7 Lead hazard assessment reports describe lead hazards identified at the time the assessment was performed. The locations, types, or severities of lead hazards can change over time as a result of property improvement or deterioration, significant changes in property use, or other factors.NOTE 3: The term “lead-free” should never be used to describe the absence of lead hazards because testing methodologies are not designed to measure the total absence of lead. Small amounts of lead present in building materials and components or soil may result in a hazard with changes in building conditions or as a result of activities that create dust that contains lead.5.8 This guide is applicable for assisting professionals, homeowners, owners or occupants of rental property, lenders, insurers, and others with a property interest in determining the presence of lead hazards.5.9 This guide also is applicable for assisting designers of lead hazard mitigation projects to target resources toward lead hazard controls that are deemed most likely to result in the prevention of lead poisoning in young children.1.1 This guide covers how to conduct, document, and report findings of a lead hazard assessment of dwellings and of other child-occupied facilities.1.2 Procedures for assessment of personal items, such as toys, dishes, and hobby materials that may contribute to elevated lead levels in blood are not included in this guide.1.3 Procedures for random sampling of units within dwellings having multiple units are not included.1.4 This guide contains notes, which are explanatory, and are not part of the mandatory requirements of this guide.1.5 The values stated in SI units are to be regarded as the standard.1.5.1 Exception—The inch-pound and SI units shown for wipe sampling data are to be individually regarded as standard for wipe sampling data.1.6 Methods described in this guide may not meet or be allowed by requirements or regulations established by local authorities having jurisdiction. It is the responsibility of the user of this standard to comply with all such requirements and regulations.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification covers child carriers that position the child ahead of the rider and behind the handlebar of a bicycle. These child carriers transport children with a minimum weight of 12 kg and a maximum weight of 27 kg who are capable of sitting unaided.1.2 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 A clearance examination of abatement areas and other areas associated with other lead-hazard control activities, or building maintenance or modification activities in single-family detached dwellings, individual units in multifamily dwellings, common areas or exterior sites, and child-occupied facilities is performed to determine that the clearance area is adequately safe for reoccupancy.4.2 It is the responsibility of the user of this standard to assure that all regulatory, contractual and personnel requirements are met prior to conduct of a clearance examination. At a minimum, users of this standard shall be trained in its use and in safe practices for its conduct.NOTE 2: Authorities having jurisdiction may have certification or specific training requirements, or both.4.3 This practice is one of a set of standards developed for lead hazard management activities. The visual assessment procedures required in this practice are found in Practice E2255/E2255M and the record keeping requirements are found in Practice E2239.4.4 Although this practice was primarily developed for dwellings and for other child-occupied facilities, this practice may be also applied to nonresidential buildings and related structures by agreement between the client and the individual conducting the clearance examination.4.5 This practice may be used by owners and property managers, including owner-occupants, and others responsible for maintaining facilities. It may also be used by lead hazard management consultants, construction contractors, labor groups, real estate and financial professionals, insurance organizations, legislators, regulators, and legal professionals.4.6 This practice does not address whether lead-hazard reduction activities or other building modification or maintenance work were performed properly.1.1 This practice covers visual assessment for the presence of deteriorated paint, surface dust, painted debris, and paint chips with environmental sampling of surface dust to determine whether a lead hazard exists at the time of sample collection, following lead-hazard reduction activities, or other building maintenance and modification activities.1.2 This practice addresses clearance examination of single-family detached dwellings (including exterior structures, such as fences), individual units in multifamily dwellings, common areas or exterior sites, and child-occupied facilities.1.3 This practice also addresses clearance examinations that may include soil sampling, for example when soil abatement has been performed.1.4 This practice includes a procedure for determining whether regulatory requirements for lead clearance levels for dust and, where warranted, soil have been met, and consequently, whether a clearance area passes or fails a clearance examination.NOTE 1: This practice is based on that portion of “clearance” described for the United States in 40 CFR Part 745 for abatement, and in 24 CFR Part 35 for lead-hazard reduction activities other than abatement.1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

3.1 This classification scheme defines the type of motions, skills, or tools required for a particular type of child-resistant package and provides examples of current packaging within that type.3.2 Reference to a particular package in this classification is not intended in any manner to denote endorsement or approval of the package by ASTM.3.3 Packages have been included as examples based on manufacturers' claims of child-resistance. Child-resistant package functionality for any specific product type must be determined by the packager/manufacturer following the guidelines of the PPPA of 1970 and the most current version of the CFR Title 16 Part 1700 and Title 40 Part 157.2 The listing of a package in this classification is not an indication of whether or not it has been successfully tested in accordance with the aforementioned guidelines.3.4 Additions or deletions to the examples should be reported to Subcommittee F02.50 on Package Design and Development, for incorporation into this classification during the next revision.3.5 Additions require F02.50 Task Group review of CFR Title 16 Part 1700 full protocol testing reports. Reports should cover procedures and all CFR Title 16 Part 1700 required reporting elements. Additional information may be requested.3.6 Use of a package cited in this classification allows for the statement “CONFORMS TO ASTM D3475,” and does not allow for the use of the ASTM logo or result in an ASTM certification mark.1.1 This classification covers various types of child-resistant packages.1.2 The examples for each type of child-resistant packaging are not intended to be all-inclusive, but are included only as an aid in the understanding and comprehension of each type of classification.1.3 Listings are not to be considered endorsements or approval of the package by ASTM.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This test method of applying force may be used as a standard test to compare the characteristics of a given design of container/child-resistant closure system with a standard or to compare the characteristics of container/child-resistant closure systems differing in construction.It may be used to simulate certain manipulations that may be expected to occur in protocol testing (such as, prying with the teeth or objects in the room, biting, and pulling with the teeth).This test method may be used to establish performance specifications.1.1 This test method covers the measurement of the force required to separate (or “shell”) the snap-fitted outer cap from the inner cap of Type IA, IB, or IC child-resistant closures.1.2 This test method does not measure the force required to separate parts of a child-resistant closure system that were originally “screwed-on” instead of “snapped-on” (for example, pull a cap over or through continuous or multi-start threads when the cap was originally screwed on).1.3 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This test method of applying force may be used as a standard test to compare the characteristics of a given design of container/child-resistant closure system with a standard or to compare the characteristics of container/child resistant closure systems differing in construction.It may be used to simulate certain manipulations that may be expected to occur in protocol testing (such as, prying with the teeth, or objects in the room, biting, and pulling with the teeth).This test may be used to establish performance specifications. Shelling force may vary with cap application torque, bottle design, and other factors. Consequently where precise comparative results are desired, these factors must be carefully controlled.1.1 This test method covers the measurement of the force required to separate (or “shell”) the snap-fitted outer cap from the inner cap of Type IA, IB, or IC child-resistant closures. See Practice D3475.1.2 This test method is an alternative to Test Method D3481, a manual test procedure.1.3 This test method does not measure the force required to separate parts of a child-resistant closure system that were originally “screwed-on” instead of “snapped-on” (for example, pull a cap over or through continuous or multi-start threads when the cap was originally screwed on).1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers rear-mounted bicycle child carriers. It does not cover child carriers mounted in front of handlebars or to the top tube, head tube, or behind the handlebars in front of the rider. The carrier shall be manufactured free of burrs, sharp edges, and sharp points; when present, these shall be properly covered with protective coatings to prevent injuries. In addition, the carrier shall be equipped with a rear reflector, footrests, backrest, armrests, protective devices to prevent contact of hands and feet with moving or movable components of the bicycle, and belt or capturing devices to keep the child from standing in or leaving the carrier. The carrier shall be protected against corrosion, with any plastic or synthetic components stabilized against ultraviolet radiation and resistant to ozone. Tests for high and low temperature resistance, high and low temperature drop, and strength shall be performed and shall conform to the requirements specified. Additional tests for flammability, sharp points, sharp edges, ambient drop, retention system pull, and retention system security may be performed as well.1.1 This specification covers child carriers that mount to the rear of bicycles in order to transport children or accessory loads with a maximum weight of 18 kg (40 lb). This specification does not apply to child carriers that mount in front of the handlebars, or to the top tube, head tube, or behind the handlebars in front of the rider.NOTE 1: In the instructions, the manufacturer must warn the rider that a load added to the bicycle will lessen the stability and alter the riding characteristics of the bicycle. This complication is particularly important when riding with children who are near the high end of the weight range.1.2 The following safety hazards caveat pertains only to the test method portions, Sections 5, 6, and 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车