4.1 Upon mutual agreement between the purchaser and the supplier, woven and knitted products intended for this end use should meet all of the requirements listed in Table 1 of this specification.4.2 It is recognized that for purposes of fashion or aesthetics, the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.4.2.1 In such cases, any references to the specification shall specify that: “This product meets ASTM Specification ____ except for the following characteristic(s).”4.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular product.4.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods. For additional information see Test Methods D629, Practice D1776, and Guide D3938.1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knit flat, fitted, and waterbed sheet products for use in institutional and household environments.1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements.1.3 The requirements in Table 1 apply to the length and width directions for those properties where fabric direction is pertinent.1.4 This specification is not applicable to woven and knit products used for sheet blankets or to woven and knitted sheet products used for apparel.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 Upon mutual agreement between the purchaser and the supplier, woven products intended for this end use should meet all of the requirements listed in Table 1 of this specification.4.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.4.2.1 In such cases, any references to the specification shall specify that: This product meets Specification D5432 except for the following characteristic(s).4.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style.4.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This specification covers the evaluation of specific performance characteristics of importance in thermal woven, conventional woven, flocked, nonwoven, and knitted blanket products for use in institutional and household environments.1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements.1.3 The requirements in Table 1 apply to the length and width directions for those properties where fabric direction is pertinent.1.4 This specification does not include requirements for electric blankets. Electric blankets are specified under UL 964 requirements dictated by the Underwriter's Laboratories.1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 Upon mutual agreement between the purchaser and the supplier, woven or knitted products intended for this end use should meet all of the requirements listed in Table 1 of this specification for terry products and Table 2 for non terry products.5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1 or Table 2. Therefore, one or more of the requirements listed in Table 1 or Table 2 may be modified by mutual agreement between the purchaser and the seller.5.2.1 In such cases, any references to the specification shall specify that: This product meets ASTM Specification 63-707 except for the following characteristic(s).5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 or Table 2 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style.5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knitted kitchen towel, dishcloth, crash towel, huck towel, washcloth, hand towel, bath towel, and bath sheet products for use in institutional and household environments.1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements.1.3 The requirements in Tables 1 and 2 apply to the length and width directions for those properties where fabric direction is pertinent.1.4 This specification is not applicable for coated and laminated products, nonwoven products, or terry fabrics used for apparel.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers the requirements for gloves made of rubber-like latex, whether made of natural or synthetic materials, unsupported with or without a flock lining, intended for household, beautician, or general use. This specification serves as a guide to permit obtaining gloves of consistent performance, and does not address the safe and proper use of gloves. Sampled specimens shall be tested and conform accordingly to dimensions (width, length, and finger and palm thickness) in accordance to size, and physical requirements (tensile strength and ultimate elongation) before and after accelerated aging. Gloves shall have surfaces that may be smooth or textured, with or without a pattern on the finger surface, and may have a rolled, natural edge or cut cuff. In any case, the gloves shall either be ambidextrous, or in pairs (right and left hand) and matched in design.1.1 This specification covers requirements for gloves made of rubber-like latex, whether made of natural or synthetic materials, unsupported with or without a flock lining, intended for household, beautician use, or general use.1.2 This specification is intended to serve as a guide to permit obtaining gloves of consistent performance. The safe and proper use of gloves is excluded from the scope of this specification.1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This guide is written for all persons involved with HHWCs, but especially for those primarily responsible for establishing and providing training to workers at HHWCs. This guide is intended to provide recommended training topics which should be covered during the initial baseline and annual refresher training. The actual topics and depth of training for each worker must be assessed by the HHWC operator on a case-by-case basis with emphasis on the particular job assignment for each worker. The major factors the operator should consider are what are the anticipated hazards to which each worker may be exposed and what are the controls/work practices which the worker must know in order to do his or her job assignments safely.Another factor which the operator must consider is the areas in which each worker is expected to work or the areas to which each worker has access to as part of job assignments. For example, if an administrative assistant only has access to the office area, and never enters the active HHWC area, then training may be limited to required actions as part of the contingency plan. If, however, the administrative assistant is periodically required to enter into the active HHWC area, more detailed training is required based on anticipated hazards which the administrative assistant may be exposed to while in the HHWC area.When deciding on the training topics for the annual refresher training, the HHWC operator must decide on topics in Section 7 which are relevant to the HHWC workers attending the refresher training class. Factors which should be considered are:4.3.1 Hazards to which the workers may be exposed to,4.3.2 Changes in the standard operating procedures, contingency plan since the previous training,4.3.3 Length of time from which a worker has received training in the topics listed in Section 7, and4.3.4 Identification of incidents, hazards, unsafe conditions, or any other situations which indicate a need to retrain workers in a particular topic to ensure a safe and healthful workplace.1.1 This guide covers recommended health and safety training topics for workers at operations for the collection of household hazardous waste or conditionally exempt small quantity generator waste, or both, regardless of the type of collection. Although this guide is intended to protect the worker, public health, and the environment, it is not intended to satisfy all the health and safety training requirements under the Occupational Safety and Health Act of 1970 or the Resource Conservation and Recovery Act of 1976. Additionally, local and state requirements may also vary. Therefore, it is recommended that the operator of a household hazardous waste collection operation also check federal, state, and local regulations for additional requirements.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this guide to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

5.1 Upon agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the seller.5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4111 except for the following characteristic(s).”5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.5.4 The uses and significance of particular properties and methods are discussed in the appropriate sections of the specified methods.1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in napery and tablecloths (household and institutional).1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This test method provides an indication of the capability of the vacuum cleaner to remove embedded dirt from carpeting. This test method is based upon results of home cleaning tests so that, in most cases, a reasonable correlation exists between home and laboratory results. The amount of dirt picked up in the laboratory test may not be the same as in the home; however, it will show that, in most cases, a vacuum cleaner that performs well in the laboratory will perform well in a home. Laboratory results may differ due to variations in the homes, carpets, dirt, and other factors (see Section 6).4.2 In order to provide a uniform basis for measuring the performance described in 1.1, standardized test carpets and a standardized test dirt are employed in this procedure.1.1 This test method covers only a laboratory test for determining the relative carpet dirt removal effectiveness of household/commercial vacuum cleaners when tested under specified conditions.1.2 This test method is applicable to household/commercial types of upright, canister, and combination cleaners.1.3 The test method applies to embedded dirt removal from carpets, not the removal of surface litter and debris.NOTE 1: The F11.21 subcommittee is actively pursuing new market relevant carpets with the assistance of the carpet industry. Although plush and Frieze carpet panels are no longer available for purchase, some laboratories may still have samples for testing. In such cases, the table values remain valid.NOTE 2: Due to the influence of environmental conditions, variations in time, origin of test materials, and proficiency of the operator, most of the described test methods will give more reliable results when applied for comparative testing of a number of appliances at the same time, in the same laboratory, and by the same operator until a new interlaboratory study has been completed to provide repeatability and reproducibility values.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 843元 / 折扣价： 717 元 加购物车

4.1 Resistance to various liquids used in the home is an important characteristic of organic finishes. These test methods provide the means by which the relative performance of coating systems may be evaluated. It should be recognized that continuous films are necessary for reliable results.1.1 This test method covers determination of the effect of household chemicals on clear and pigmented organic finishes, resulting in any objectionable alteration in the surface, such as discoloration, change in gloss, blistering, softening, swelling, loss of adhesion, or special phenomena.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This test method will provide an indication of the ability of the vacuum cleaner in removing dry debris from hard surface floors. The cleaning ability in the laboratory test will not be the same as in home cleaning; however, in most cases, a vacuum cleaner that performs well in the laboratory will clean well in a home.4.2 To provide a uniform basis for measuring the performance described in 1.1, standardized test hard surface flooring and standardized test debris are used.1.1 This test method provides only a laboratory test for determining the relative hard surface floor-cleaning ability of household/commercial vacuum cleaners when tested under specified test conditions.1.2 This test method is applicable to household/commercial types of upright, canister, combination, and stick vacuum cleaners that use a dry primary dirt receptacle and are intended for cleaning hard surface floors as a primary or secondary function.1.3 This test method applies only to the removal of dry debris from hard surface floors, not the removal of embedded dirt from carpet.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This specification may be used to evaluate pertinent performance characteristics of washable and drycleanable soft window coverings, whether lined or unlined.4.1.1 Soft window covering characteristics to be evaluated prior to repeated refurbishing include, but are not limited to, seam strength and appearance, uniformity of shade (part to part), and size consistency (side to side and part to part).4.1.2 Soft window covering characteristics to be evaluated after repeated refurbishing include, but are not limited to, colorfastness, dimensional change, seam strength, appearance, and compatibility of components. Compatibility of dimensional change between drapery fabric and lining should be noted.4.2 The specified home laundry machine settings do not reflect advances in cycle design or special features of washer and dryers which enhance the performance of these products. The standard washing and drying procedure reflects the minimum capabilities of current home laundering equipment used by consumers in accordance with care label instructions.4.2.1 The reproducibility of the results of the test method specified in 9.2 depends on the use of procedures for automatic home laundering as specified on care labels.4.3 The areas to be evaluated and the criteria assigned to these areas shall be set by mutual agreement between purchaser and supplier.AbstractThis performance specification establishes the evaluation of specific performance characteristics of any washable or dry-cleanable soft window covering fabrics, whether lined or unlined, for household use. The characteristics to be evaluated prior to repeated refurbishing include, but are not limited to, seam strength and appearance, uniformity of shade (part to part), and size consistency (side to side and part to part). Consequently, the characteristics to be evaluated after repeated refurbishing include, but are not limited to, colorfastness, dimensional change, seam strength, appearance, and compatibility of components. Compatibility of dimensional change between drapery fabric and lining should be noted.1.1 This specification covers the evaluation of specific performance characteristics of any washable or drycleanable soft window covering.1.2 This specification is not a specification for washable or drycleanable soft window coverings but may be used by mutual agreement between the purchaser and the supplier to establish material specifications.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 The methods outlined in this guide can be used to qualitatively and quantitatively evaluate the sensory characteristics and performance of trigger hard surface household cleaning products for nonporous surfaces.5.2 The methods are suited for descriptive analysis and may be adaptable for consumer acceptance research.5.3 This guide provides the procedure for the evaluation of package, application, performance, after-use and fragrance aspects of hard surface cleaners. Depending on the test objectives, all or some of these measures may be used.5.4 This guide is designed for use for product research guidance in product formulation, new product development, and quality control issues.5.5 This guide is a compendium of information or series of options that does not recommend a specific course of action. This guide is not intended for claim substantiation, as it has not been subjected to validation testing.5.6 This guide is for use by individuals who familiarize themselves with these procedures and who have previous experience with sensory evaluations. It is suggested that the individuals have some experience with developing and training a descriptive panel or work under the supervision of a sensory professional who has.5.7 This guide might involve hazardous materials. This guide does not claim to address all of the safety problems associated with its use. It is the responsibility of the user of this guide to establish appropriate safety and healthy practices and to determine the applicability of limitations prior to use.1.1 This guide presents guidelines specific to the sensory evaluation of trigger hard surface cleaners. It covers the procedure for preparing a nonporous surface with the intent to measure one or all of the various aspects of a trigger product: package, application, performance, and after-use properties, with focus on visual, tactile, fragrance, performance, and package ergonomics. It is applicable for use with assessors, highly trained assessors, and consumers.1.2 This guide for preparing nonporous hard surfaces is intended to focus on surface preparation and evaluation, not on panel selection, training, or development.1.3 The reader should be aware that good sensory practices are required when preparing the surfaces, and in developing and training the assessors.1.4 The researcher is responsible for identifying the most appropriate test design and using the appropriate statistical tool to address that experimental design.1.5 Since this guide's intended use is to provide direction on the presentation and measurement of the different aspects of spray trigger hard surface cleaners, this guide may not accurately represent all possible soils and surfaces where spray trigger hard surface cleaners may be used.1.6 This guide provides suggested procedures and is not meant to exclude alternate procedures that may be effectively used to provide the same results.1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values are stated in only SI units when inch-pound units are not used in practice.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This guide is intended to provide general guidance to HHW programs for accepting and segregating materials, selecting a management method, and packaging materials collected by HHW programs.1.1 This guide covers Household Hazardous Waste (HHW) programs for accepting, segregating, and packaging materials collected through HHW programs to minimize the risk associated with managing these materials and to identify applicable regulations. This guide does not address storing, vehicle loading, or transporting collected and packaged materials. This guide does not attempt to define the hazardous nature of materials.1.2 Certain existing local, state, and federal regulations apply to HHW program operations. This guide does not replace these existing regulations, and is not intended to be used as the basis for regulations for HHW programs. This guide does not reference all applicable applications, since applicable regulations will vary. HHW programs should research all applicable regulations before establishing a materials collection program.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this guide to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 The test results provide an indication of the turbine-powered nozzle life. The end of turbine life will be judged in accordance with 3.1.1.1.1 This test method covers the turbine-powered nozzle used in household central vacuum cleaning systems.1.2 This test method provides a test for determining the operating turbine life in hours by an accelerated laboratory procedure. The turbine is tested while mounted and operated in the power nozzle.1.3 This test method covers only the turbine-powered nozzle. The system used to provide the airflow source is not under consideration.1.4 This test method is limited to the determination of turbine life for a household turbine-powered nozzle.1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 Fabrics intended for this end-use should meet all of the requirements listed in Table 1.(A) There is more than one standard test method that can be used to measure breaking strength, bursting strength, tear strength, and lightfastness. These test methods cannot be used interchangeably since there may be no overall correlation between them (see Note 2, Note 3, Note 4, Note 5, and Note 9).(B) Class in colorfastness and SA rating is based on a numerical scale of 5.0 for negligible color change, color transfer, or wrinkling to 1.0 for very severe color change, color transfer, or wrinkling. The numerical rating in Table 1 or higher is acceptable.(C) AATCC Gray Scale for Color Change.(D) AATCC Gray Scale for Staining.(E) AATCC 9-Step Chromatic Transference Scale.(F) For durable-press fabrics only.(G) The development of a standard method has been referred to the American Association of Textile Chemists and Colorists.4.2 It should be recognized that fabric can be produced utilizing an almost infinite number of construction variables (e.g., type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finished). Additionally, fashion and aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1.4.2.1 Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use.4.3 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This performance specification covers the requirements for all knit, lace, foam back, stitch-bonded, conventional weights, and sheer woven fabrics to be used in the manufacture of curtains and draperies.1.2 This performance specification is applicable to all fabrics except those made of glass.1.3 For those properties where fabric direction is pertinent, these requirements apply to the length and width directions for woven fabric and to both the wale and course directions for knit fabric.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This practice is useful for the selection of zippers that will be compatible with items to be care labeled.4.2 This practice is useful as a guide for the selection of test methods to evaluate zipper properties that are relevant to care-labeled items.1.1 This practice provides guidelines to the manufacturer for the selection of zippers to be used in garments and household furnishings that have care labels. The use of this practice will facilitate the selection of a zipper compatible with the end-item requirements. In the absence of complete knowledge of end-item characteristics, it is not possible to stipulate specific universal characteristics for a care label. Therefore following initial selection, the chosen zipper should be tested in a prototype item to confirm its suitability. Zipper properties to be considered are those that may, following refurbishing, be the ones likely to adversely affect the continued use and enjoyment of the item in which the zipper is installed.1.2 The product characteristics evaluated by this practice are shrinkage, colorfastness, and ironing deformation.NOTE 1: Test methods of interest include Test Method D2052, Test Method D2053, Test Method D2054, Test Method D2057, Test Methods D2060.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车