This specification covers the requirements for plates, sheets, strips, and rolled bars of copper-zinc-tin and copper-zinc-tin-iron-nickel alloys with Copper Alloy UNS Nos. C40500, C40810, C40850, C40860, C41100, C41300, C41500, C42200, C42500, C42520, C43000, and C43400. Materials shall be processed by hot working, cold working, and annealing as to produce a uniform wrought structure in the finished product. Tempers shall be available in the rolled, as hot rolled, or annealed conditions. Products shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (thickness, length, width, mass, straightness, and edges), mechanical (tensile strength, and Rockwell hardness), chemical composition, and grain size requirements.1.1 This specification establishes the requirements for specified copper-zinc-tin alloys and copper-zinc-tin-iron-nickel alloys plate, sheet, strip, and rolled bar. The alloys and nominal compositions are as follows:Copper AlloyUNS No. Copper,% Tin,% Zinc,% Phos.,% Iron,% Nickel,%             C40500 95 1 4      C40810 95.5 2.0 2.2 0.03 0.1 0.15C40850 95.5 3.0 1.3 0.1 0.1 0.1C40860 94.8 2.0 3 0.03 0.03 0.1C41100 91 0.5 8.5      C41300 91 1 8      C41500 91 2 7      C42200 87 1 12      C42500 88 2 10      C42520 89.8 2.0 8 0.1 0.1 0.1C43000 85 2 13      C43400 85 0.7 14.3      1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.2.1 Exception—Average grain size in Table 3 is stated in SI units.1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification:1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the requirements for plates, sheets, strips, and rolled bars of copper-zinc-aluminum-cobalt (Copper Alloy UNS No. C68800) and copper-zinc-tin-iron (Copper Alloy UNS No. C66300) alloys. The material for manufacture shall be a cast bar, cake, slab or so forth of such purity and soundness as to be suitable for processing by hot working, cold working, and annealing to produce a uniform wrought structure in the finished product. Products shall be produced in tempers H (rolled), and O (annealed to temper). Products shall be tested to examine their conformance to dimensional (mass, thickness, length, straightness, and edge), mechanical (tensile strength, and Rockwell hardness), electrical (resistivity and equivalent conductivity), chemical composition, and grain size requirements.1.1 This specification establishes the requirements for Copper Alloy UNS C66300 and C68800 plate, sheet, strip, and rolled bar.2NOTE 1: Since alloy C68800 is frequently used in a variety of applications where yield strength and stress-corrosion resistance may be critical, it is recommended that drawings or samples of the part to be fabricated and details of application be submitted for use in establishing temper and treatment of material.1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification establishes the requirements for flat copper wire and strip products, with rolled or drawn finished edges produced for general applications. Unless otherwise established by agreement between the manufacturer and purchaser, products shall be produced in UNS Copper Nos. C10100, C10200, C10300, C10500, C10700, C10800, C11000, C11040, C12200, and C14200. The material for manufacture shall be a billet, cake, wire bar, or rod suitable for processing by hot working, cold working, and annealing to produce a uniform wrought structure in the finished product. Products shall be produced in the annealed (O61) and cold worked (H00, H01, H02, H03, H04, H06, and H08) tempers. Products shall be tested and shall adhere to dimensional (thickness, width, length, straightness, and edge contour), mechanical (tensile strength, elongation, Rockwell hardness, bend angle, and hydrogen embrittlement susceptibility), electrical resisitvity, and chemical composition requirements.1.1 This specification establishes the requirements for copper products, flat wire and strip, with rolled or drawn finished edges produced for general application.1.1.1 The product is produced in UNS Copper Nos. C10100, C10200, C10300, C10500, C10700, C10800, C11000, C11040, C12200, and C14200 unless otherwise established by agreement between manufacturer and purchaser.1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.NOTE 1: When a copper other than that listed in 1.1.1 is designated by the purchaser, the resulting product shall conform to the physical, mechanical, performance, dimensional, and tolerance requirements per agreement between the manufacturer and purchaser.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the general requirements for hot-rolled, heavy-thickness, and high-strength low-alloy with improved formability sheet and strip coils. These coils are normally produced from rimmed, capped, or semi-killed steel. Steels may be produced as ingot-cast or strand-cast. Cast or heat analysis shall be made to determine the conformance with the requirements. For steels other than non-killed (capped or rimmed), product analysis may be made. The chemical analysis shall conform to the specified amounts of carbon, manganese, phosphorus, sulfur, silicon, and copper. Steels may or may not be subjected to tension test requirement. Specimen preparation and test methods are discussed. The mechanical property requirements, number of specimens, test locations, and specimen orientation shall be in accordance with the applicable product specification. Tolerances for the dimensions of sheet and strip coils are specified.1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils.1.2 It applies to Specifications A414/A414M, A424/A424M, A1018/A1018M, and A1031/A1031M.1.3 This material is available only in coils described as follows:  Size Limits, Coils Only     Product Width, in. [mm] Thickness, in. [mm]     Strip over 8 to 12, incl[over 200 through 300] 0.230 to 1.000, incl[from 6.0 through 25]Sheet All WidthsAAll Widths 0.230 to 1.000, incl[from 6.0 through 25]NOTE 1: The changes in width limits with the publication of A635/A635M – 06a result in a change in tensile testing direction for material from 0.180 in. [4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in. [1200 mm] wide, as that material is now covered by Specification A568/A568M – 06a. The purchaser is advised to discuss this change with the supplier.1.4 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.1.5 For the purposes of determining conformance with this and the appropriate product specifications referenced in 1.2, measured values, calculated values, and observed values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.1.5.1 Ordered values, identified in tables, specified such as over 30 through 48, or 30 exclusive to 48 inclusive, covers all ordered values specified as 30.1, 30.01, 30.001, etc., up to and including 48.000 etc., but does not cover ordered values specified as 30.000 etc. or less, nor does it cover ordered values specified as 48.1, 48.01, 48.001, etc., in accordance with the absolute method of Practice E29.1.6 Annex A1 lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification is used.NOTE 2: The term weight is used when inch-pound units are the standard. However, under SI, the preferred term is mass.1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.8 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1.1 This specification covers high-strength, low-alloy columbium, or vanadium hot-rolled sheet and strip, or cold-rolled sheet, or combinations thereof, in either cut lengths or coils, intended for applications where greater strength and savings in weight are important. The material is available as two classes. They are similar in strength level except that Class 2 offers improved weldability and more formability than Class 1. Atmospheric corrosion resistance of these steels is equivalent to plain carbon steels. With copper specified, the atmospheric corrosion resistance is twice that of plain carbon steel.1.2 The value stated in inch-pound units are to be regarded as the standard.1.3 Class 1 material was previously A607 without a class designation.

定价： 0元 / 折扣价： 0 元

1.1 This specification covers cold-rolled carbon structural steel (SS) sheet, in cut lengths or coils. It includes five strength levels designated as Grade A with yield point 25 ksi (170 MPa) minimum; Grade B with 30 ksi (205 MPa) minimum; Grade C Types 1 and 2 with 33 ksi (230 MPa) minimum; Grade D Types 1 and 2 with 40 ksi (275 MPa) minimum; and Grade E with 80 ksi (550 MPa) minimum.1.2 Grades A, B, C, and D have moderate ductility whereas Grade E is a full-hard product with no specified minimum elongation.1.3 The values stated in inch-pound units are to be regarded as the standard.

定价： 0元 / 折扣价： 0 元

1.1 This specification covers hot-rolled heavy-thickness carbon-steel sheet and strip of structural quality in coils beyond the size limits of Specification A570/A570M. This material is intended for structural purposes where mechanical test values are required and is available in the sizes listed below. This material is available only in coils as described below: Size Limits, Coils Only Product Width, in. (mm) Thickness, in. (mm) Strip over 8 to 12 0.230 to 0.750, incl (200 to 300) (6.0 to 19) Sheet over 12 to 48 0.230 to 0.750, incl (300 to 1200) (6.0 to 19) over 48 (1200) 0.180 to 0.750, incl (4.5 to 19) 1.1.1 The following grades are covered in this specification: Mechanical Properties Yield Point min, Tensile Strength Grade ksi (MPa) min, ksi (MPa) 30 30 (205) 49 (340) 33 33 (230) 52 (360) 36 36 (250) 53 (365) 40 40 (275) 55 (380) 1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values of the two systems may result in nonconformance with this specification. 1.3 Sheet and strip in coils of the sizes noted in 1.1 can be included in this specification only with the following provisions: 1.3.1 The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A6/A6M (plates provided from coils) or A20/A20M (plates produced from coils), 1.3.2 This specification is not applicable to the steels covered by Specification A635/A635M, 1.3.3 The dimensional tolerances from Specification A635/A635M are applicable to material produced in accordance with this specification, 1.3.4 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming, and 1.3.5 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations.

定价： 0元 / 折扣价： 0 元

1.1 This specification covers cold-rolled carbon drawing steel (DS) sheet, in coils or cut lengths. This material is intended for fabricating identified parts where particularly severe drawing or forming may be involved or essential freedom from aging is required.1.2 This specification is applicable for orders in either inch-pound units (as A 620) or SI units (as A 620M).

定价： 0元 / 折扣价： 0 元

1.1 This specification covers hot-rolled carbon steel sheet and strip of drawing quality, special killed, in coils or cut lengths. This material is intended for use in fabricating identified parts where particularly severe drawing or forming may be involved and surface appearance is usually not of primary importance.1.2 This specification is applicable for orders in either inch-pound units (as A 622) of SI units (as A 622M).

定价： 0元 / 折扣价： 0 元

This specification covers hot-rolled carbon steel sheet and strip, in coils and cut lengths. The cast or heat analysis of the steel shall conform to the chemical composition for copper, nickel, chromium, molybdenum, vanadium, and columbium. The bending properties are measured.1.1 This specification covers hot-rolled carbon steel (CS) sheet and strip, in coils and cut lengths, in which the maximum of the specified carbon range is over 0.15 and not over 0.25 % and the maximum of the specified manganese range is not over 0.90 %. This material is ordered to chemical composition.1.2 This specification is not applicable to the steels covered by Specification A635/A635M.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification concerns general procedures for specifying requirements of flat-rolled electrical steels for magnetic applications. This specification is to be used when the material in question is not covered by an ASTM material specification. The specification does not contain requirements but instead lists physical properties, ordering information and other attributes that should be considered when purchasing the material. All ASTM electrical steel specifications are in conformity to this specification.1.1 This specification covers general procedures for specifying requirements in the procurement and delivery of flat-rolled electrical steels for magnetic applications. When an applicable individual specification does not exist, this specification enables the user to order a suitable material to be supplied under controlled conditions with respect to magnetic quality, sampling, testing, packaging, and so forth, by specifying certain requirements on the purchase order and citing this specification.1.2 Individual ASTM electrical steel specifications that are in conformity with this specification are Specifications A677, A683, A726, A840, A876, and A1086.NOTE 1: For more information on other standards associated with this specification, refer to the following: Test Methods A341/A341M, A343/A343M, A348/A348M, A596/A596M, A712, A717/A717M, A719/A719M, A720/A720M, A721/A721M, A773/A773M, A804/A804M, A889/A889M, A937/A937M, A971/A971M, and Practice A664.1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to customary (cgs-emu and inch-pound) units which are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This specification establishes the requirements for plate, sheet, strip, and rolled bar copper alloy UNS No. C15815, dispersion strengthened copper (DSC), which has been modified by the addition of natural or enriched boron for absorption of neutrons. 1.1.1 The products made to this specification are under consideration for use in storage containers for spent nuclear fuel. Note 1- Dispersion strengthened copper is thermally stable high-strength copper which retains a high percentage of its strength at elevated temperature. In addition, it does not recrystallize or soften after exposure to high temperatures almost to the melting point of copper. Since dispersion strengthened copper uses inert aluminum oxide particles to strengthen the copper matrix, the thermal conductivity of the copper is not significantly decreased. Note 2- Borated dispersion strengthened coppers covered by this specification, because of their particular structure and specialized properties, may require special care in their fabrication and welding. 1.2 The values stated in inch-pound units are the standard. SI units are provided for information only.

定价： 0元 / 折扣价： 0 元

This specification covers annealed, drawn or rolled iron-chromium-aluminum alloy shapes used for electrical heating and resistance purposes. This specification contains the requirements for chemical composition, electrical resistance, mechanical properties and temperature-dependent changes in resistance of the alloys.1.1 This specification covers annealed, drawn, or rolled shapes for electrical heating and resistance purposes of alloys consisting mainly of iron, chromium, and aluminum as detailed in Table 1.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This specification covers hot-rolled, heavy-thickness, high-strength, low-alloy columbium, or vanadium hot-rolled sheet and strip, or combinations thereof, in coils beyond the size limits of Specification A607. This material is intended for miscellaneous applications where greater strength and savings in weight are important. The material is available as two classes. They are similar in strength level, except that Class 2 offers improved weldability and more formability than Class 1. Atmospheric corrosion resistance of these steels is equivalent to plain carbon steels. With copper specified, the atmospheric corrosion resistance is somewhat enhanced. Note 1-For methods of establishing the atmospheric corrosion resistance of low-alloy steels see Guide G101. 1.1.1 This material is available only in coils described as follows: Size Limits, Coils Only Product Width, in. (mm) Thickness, in. (mm) Strip Over 8 to 12 0.230 to 0.750, incl (Over 200-300) (Over 6.0 to 19) Sheet Over 12 to 48 0.230 to 0.750, incl (Over 300-1200) (Over 6.0 to 19) Over 48 (Over 1200) 0.180 to 0.750, incl (Over 4.5 to 19) 1.2 Sheet and strip in coils of sizes noted in 1.1 can be included in this specification only with the following: 1.2.1 The material is not to be converted into steel plates for structural or pressure vessel use. 1.2.2 This specification is not applicable to the steels covered by Specification A635/A635M. 1.2.3 The dimensional tolerances of Specification A635/ A635M are applicable to material produced to this specification. 1.2.4 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming. 1.2.5 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

定价： 0元 / 折扣价： 0 元

1.1 This specification covers heavy thickness high-strength, low-alloy hot-rolled sheet and strip, in coils beyond the size limits of Specification A715. The product has improved formability when compared with steels covered by Specification A935/A935M. The product is furnished only as coils and is available in four-strength levels, Grades 50, 60, 70 and 80 (345, 415, 485, 550) (corresponding to minimum yield strength (see Table 1)). The steel is killed, made to a fine grain practice, and includes microalloying elements such as columbium, titanium, vanadium, zirconium, etc. The steel may be treated to achieve inclusion control. The product is intended for miscellaneous applications where higher strength, savings in weight, improved formability, and weldability are important. Atmospheric corrosion resistance of these steels is equivalent to plain carbon steels. With copper specified, the atmospheric corrosion resistance is somewhat enhanced. Note 1-For methods of establishing the atmospheric corrosion resistance of low-alloy steels, see Guide G101. 1.1.1 This material is available only in coils described as follows: Size Limits, Coils Only Product Width, in. (mm) Thickness, in. (mm) Strip Over 8 to 12 (Over 200-300) 0.230 to 0.750, incl (Over 6.0 to 19) Sheet Over 12 to 48 (Over 300-1200) 0.230 to 0.750, incl (Over 6.0 to 19) Over 48 (Over 1200) 0.180 to 0.750, incl (Over 4.5 to 19) 1.2 Sheet and strip in coils of sizes noted in 1.1 can be included in this specification only with the following: 1.2.1 The material is not to be converted into steel plates for structural or pressure vessel use. 1.2.2 This specification is not applicable to the steels covered by Specification A635/A635M. 1.2.3 The dimensional tolerances of Specification A635/ A635M are applicable to material produced to this specification. 1.2.4 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming. 1.2.5 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

定价： 0元 / 折扣价： 0 元