定价： 78元 / 折扣价： 67 元

定价： 78元 / 折扣价： 67 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This specification covers the red pigment commercially known as pure toluidine red toner. The pigment may be purchased in the dry form or as a paste in oil.

定价： 0元 / 折扣价： 0 元

This specification covers palladium in the form of rod, wire, strip, and sheet material for electrical contacts. Raw materials shall be of such quality and purity that the finished product (produced by cold working, annealing, turning, grinding, or pickling as are required) will have the properties and characteristics prescribed in this specification. The material shall conform to the chemical composition requirements prescribed for palladium, platinum group (iridium, platinum, rhodium, osmium, and ruthenium), gold, silver, and copper, total impurities, lead, antimony, bismuth, tin, arsenic, cadmium, zinc, iron, and other elements. Ultimate tensile strength, elongation, microhardness (Knoop or Vickers), hardness (Rockwell or Rockwell Superficial), or a combination of these mechanical properties may be specified as temper criterion. Tension and hardness tests shall be conducted to determine conformity to the ultimate tensile strength and elongation, and Rockwell and Knoop hardness, respectively. Inspection of furnished material shall be done by temper test, dimensional test, and spectrographic or chemical analysis when needed.1.1 This specification covers palladium in the form of rod, wire, strip, and sheet material for electrical contacts.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This test method is suitable for setting specification, for use as an internal quality control tool, and for use in development or research work on industrial aromatic hydrocarbons and related materials. In addition to the pure liquid chemicals for which expansion functions are known, it may also be used for liquids for which temperature expansion data are not available, or for impure liquid chemicals if certain limitations are observed. Information derived from this test can be used to describe the relationship between weight and volume.1.1 This test method describes a simplified procedure for the measurement of density or relative density of pure liquid chemicals for which accurate temperature expansion functions are known. It is restricted to liquids having vapor pressures not exceeding 79 993 Pascal (0.800 bar, 600 mm Hg (0.789 atm) at the equilibration temperature, and having viscosities not exceeding 15 cSt at 20°C.1.2 Means are provided for reporting results in the following units:Density g/cm3 at 20°CDensity g/mL at 20°CRelative density 20°C/4°CRelative density 15.56°C/15.56°CNOTE 1: This test method is based on the old definition of  1 L = 1.000028 dm3 (1 mL = 1.000028 cm3). In 1964 the General Conference on Weights and Measures withdrew this definition of the litre and declared that the word “litre” was a special name for the cubic decimetre, thus making 1 mL = 1 cm3 exactly.NOTE 2: An alternative method for determining relative density of pure liquid chemicals is Test Method D4052.1.3 In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 8, Hazards.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 0元 / 折扣价： 0 元

定价： 590元 / 折扣价： 502 元 加购物车

1. Scope 1.1 This Standard specifies the requirements for air conduction pure tone audiometers used in determining the hearing threshold level of an individual in comparison with the standard reference threshold levels. These audiometers may be manual

定价： 319元 / 折扣价： 272 元

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

1.1 This specification covers the red pigment commercially known as pure para red toner. It is available in two Types: Type I, light, and Type II, dark.

定价： 0元 / 折扣价： 0 元

This PDF includes GI #2. 1. Scope 1.1 This Standard specifies procedures and requirements for Pure Tone Air Conduction Threshold Audiometry, without masking, used in hearing conservation programs. It is especially applicable to individuals whose he

定价： 410元 / 折扣价： 349 元