定价： 975元 / 折扣价： 829 元 加购物车

定价： 975元 / 折扣价： 829 元 加购物车

5.1 This practice is intended solely for the evaluation of metallic-coated, painted metallic-coated, and painted nonmetallic-coated materials used for the manufacture of cold formed framing members.5.2 Correlation and extrapolation of corrosion performance based on exposure to the test environment provided by Practice B117 are not always predictable. Correlation and extrapolation should be considered only in cases where appropriate corroborating long-term atmospheric exposures have been conducted.5.3 This practice assesses whether coated materials not currently in Specification A1003/A1003M satisfy the required minimum corrosion characteristics.1.1 This practice covers procedures for establishing the acceptability of metallic-coated steel sheet, painted metallic-coated steel sheet, and painted nonmetallic-coated steel sheet for use as cold formed framing members.1.2 This practice shall be used to assess the corrosion resistance of different coatings on steel sheet in a laboratory test. It shall not be used as an application performance standard for the cold formed framing members.1.3 The practice shall be used to evaluate coatings under consideration for addition to Specification A1003/A1003M.1.4 The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.1.5 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of the standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This practice provides a means by which the purchaser can determine the conformance of geosynthetic properties as applied to the acceptance or rejection of a material in regards to a material specification.4.2 This practice has been developed with strong emphasis on practicality and the realization that all geosynthetics are subjected to a vigorous quality control program prior to shipping.NOTE 1: It is suggested that the user obtain the mean, standard deviation, and/or the coefficient of variation for given physical/mechanical properties of a product directly from the manufacturer. If this data is unavailable, it is suggested that users of this practice begin to accumulate data that can be used to estimate product averages and standard deviations for each product.NOTE 2: The risk to the purchaser of buying out-of-specification materials is minimal when conformance requirements are detailed in the purchase specification and adequate conformance testing is performed. It is the producer's responsibility to perform thorough quality control testing for all properties requiring certification. The producer's risk of rejection is minimal with the performance of this thorough quality control testing.1.1 This practice covers a procedure for determining the conformance of geosynthetic properties to standard specifications.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This practice is intended to assist the various technical committees in the use of uniform methods of indicating the number of digits which are to be considered significant in specification limits, for example, specified maximum values and specified minimum values. This practice is also intended to be used in determining conformance with specifications when the applicable ASTM specifications or standards make a direct reference.1.1 This practice is intended to assist the various technical committees in the use of uniform methods of indicating the number of digits which are to be considered significant in specification limits, for example, specified maximum values and specified minimum values. Its aim is to outline methods which should aid in clarifying the intended meaning of specification limits with which observed values or calculated test results are compared in determining conformance with specifications.1.2 This practice is intended to be used in determining conformance with specifications when the applicable ASTM specifications or standards make direct reference to this practice.1.3 Reference to this practice is valid only when a choice of method has been indicated, that is, either absolute method or rounding method.1.4 The system of units for this practice is not specified. Dimensional quantities in the practice are presented only as illustrations of calculation methods. The examples are not binding on products or test methods treated.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 2548元 / 折扣价： 2166 元

Information technology - Coding of audio-visual objects - Part 4: Conformance testing AMENDMENT 11: Parametric stereo conformance

定价： 364元 / 折扣价： 310 元

5.1 Continuous opacity monitors are required to be installed at many stationary sources of air pollution by federal, state, and local air pollution control agency regulations. EPA regulations regarding the design and performance of opacity monitoring systems for sources subject to “Standards of Performance for New Stationary Sources” are found in 40 CFR 60, Subpart A General Provisions, §60.13 Monitoring Provisions, Appendix B, Performance Specification 1, and in applicable source-specific subparts. Many states have adopted these or very similar requirements for opacity monitoring systems.5.2 Regulated industrial facilities are required to report continuous opacity monitoring data to control agencies on a periodic basis. The control agencies use the data as an indirect measure of particulate emission levels and as an indicator of the adequacy of process and control equipment operation and maintenance practices.5.3 EPA Performance Specification 1 provides minimum specifications for opacity monitors and requires source owners or operators of regulated facilities to demonstrate that their installed systems meet certain design and performance specifications. Performance Specification 1 adopts this ASTM practice by reference so that manufacturers can demonstrate conformance with certain design specifications by selecting and testing representative instruments.5.4 Experience demonstrated that EPA Performance Specification 1 prior to the Aug. 10, 2000 revisions did not address all of the important design and performance parameters for opacity monitoring systems. The additional design and performance specifications included in this practice are needed to eliminate many of the performance problems that were previously encountered. This practice also provides purchasers and vendors flexibility, by designing the test procedures for basic transmissometer components or opacity monitors, or in certain cases, complete opacity monitoring systems. However, the specifications and test procedures are also sufficiently detailed to support the manufacturer’s certification and to facilitate independent third party evaluations of the procedures used.5.5 Purchasers of opacity monitoring equipment meeting all of the requirements of this practice are assured that the opacity monitoring equipment meets all of the applicable requirements of EPA Performance Specification 1 for which the manufacturer can certify conformance. Purchasers can rely on the manufacturer’s published operating range specifications for ambient temperature and supply voltage. These purchasers are also assured that the specific instrument has been tested at the point of manufacture and demonstrated to meet the manufacturer’s performance specifications for instrument response time, calibration error (based on pathlength measurements provided by the end user), optical alignment, and the spectral response performance check requirement. Conformance with the requirements of this practice ensures conformance with all of the requirements of 40 CFR 60, Appendix B, Performance Specification 1 except those requirements for which tests are required after installation.5.6 The original manufacturer, or those involved in the repair, remanufacture, or resale of opacity monitors can use this practice to demonstrate that the equipment components or opacity monitoring systems provided meet, or exceed, or both, appropriate design and performance specifications.5.7 The applicable test procedures and specifications of this practice are selected to address the equipment and activities that are within the control of the manufacturer; they do not mandate testing of the opacity system data recording equipment or reporting.5.8 This practice also may serve as the basis for third party independent audits of the certification procedures used by manufacturers of opacity monitoring equipment.5.9 This practice does not address ongoing quality assurance procedures which are needed to maintain correct operation during the lifetime of the opacity monitor.1.1 This practice covers the procedure for certifying continuous opacity monitors. In the main part of this practice, it includes design and performance specifications, test procedures, and quality assurance requirements to ensure that continuous opacity monitors meet minimum design and calibration requirements, necessary in part, for accurate opacity monitoring measurements in regulatory environmental opacity monitoring applications subject to 10 % or higher opacity standards. In Annex A1, additional or alternative specifications are provided for certifying opacity monitors intended for use in applications where the opacity standard is less than 10 %, or where the user expects the opacity to be less than 10 % and elects to use the more restrictive criteria in Annex A1. In both cases, the error budgets for the opacity measurements are given in Appendix X1.1.2 This practice applies specifically to the original manufacturer, or to those involved in the repair, remanufacture, or resale of opacity monitors.1.3 Test procedures that specifically apply to the various equipment configurations of component equipment that comprise either a transmissometer, an opacity monitor, or complete opacity monitoring system are detailed in this practice.1.4 The specifications and test procedures contained in the main part of this practice have been adopted by reference by the United States Environmental Protection Agency (U.S. EPA). For each opacity monitor or monitoring system that the manufacturer demonstrates conformance to this practice, the manufacturer may issue a certificate that states that opacity monitor or monitoring system conforms with all of the applicable design and performance requirements of 40 CFR 60, Appendix B, Performance Specification 1 except those for which tests are required after installation.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 843元 / 折扣价： 717 元 加购物车

Information technology - Coding of audio-visual objects - Part 4: Conformance testing AMENDMENT 2: MPEG-4 conformance extensions for XMT and media nodes

定价： 182元 / 折扣价： 155 元

Information technology - Coding of audio-visual objects - Part 4: Conformance testing AMENDMENT 2: MPEG-4 conformance extensions for XMT and media nodes

定价： 182元 / 折扣价： 155 元

Information technology - Coding of audio-visual objects - Part 4: Conformance testing AMENDMENT 4: IPMPX conformance extensions

定价： 182元 / 折扣价： 155 元

Information technology - Coding of audio-visual objects - Part 4: Conformance testing AMENDMENT 5: Conformance extensions for error-resilient simple scalable profile

定价： 182元 / 折扣价： 155 元

Information technology - Coding of audio-visual objects - Part 4: Conformance testing AMENDMENT 6: Advanced Video Coding conformance

定价： 1183元 / 折扣价： 1006 元

Information technology - Coding of audio-visual objects - Part 4: Conformance testing AMENDMENT 7: AFX conformance extensions

定价： 1320元 / 折扣价： 1122 元

定价： 637元 / 折扣价： 542 元