定价： 819元 / 折扣价： 697 元 加购物车

定价： 819元 / 折扣价： 697 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 605元 / 折扣价： 515 元 加购物车

定价： 936元 / 折扣价： 796 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

4.1 These test methods are designed for use in most cases with the actual equipment to be used in load handling.4.2 These test methods may be used in evaluating the shipping unit as to suitability for mechanical handling by standard user-specified load-handling equipment.4.3 These test methods will allow the user to determine integrity and stability of the load as well as provide guidance to improve the design of the unit load where deficiencies are found.4.4 Damage to products or packages observed during testing may be expected to correlate at least in a qualitative way to damage observed in actual distribution handling systems.1.1 These test methods are suitable for testing the integrity of unitized loads and large cases and crates, but not individual drums or palletized drums, as well as the ability of the contents to endure normal handling, using standard mechanical handling equipment. Not all of the test methods are applicable to all products containers and loads. These test methods are applicable to common means of material handling, including pull pack, clamp truck, and spade lift-type handling equipment as follows:1.1.1 Test Method A—Fork Truck Handling—For testing the ability of the shipping unit to withstand repeated handlings by this test method.1.1.2 Test Method B—Spade Lift Test—For lifting by spade lift attachment to determine the ability of the handling flap of the case or shipping unit to withstand repeated lifting and handling by this test method.1.1.3 Test Method C—Clamp Handling Test—For lifting by hydraulic clamp attachment, to determine the ability of the shipping unit to withstand squeeze clamp handling consisting of repeated side compression and lifting.1.1.4 Test Method D—Push-Pull Handling Test—For testing the ability of a unitized load on a slip-sheet to withstand repeated handling by this test method.1.1.5 Test Method E—Grabhook Test—For lifting by grabhooks to determine the ability of the shipping unit to withstand the horizontal pressures of grabhooks.1.1.6 Test Method F—Sling Tests—For lifting by wire rope, cable, or woven fiber slings to determine the ability of the shipping unit to withstand the compression of slings.1.2 Additional Test Methods: 1.2.1 Additional test methods that apply to mechanical handling and rough handling tests of unitized loads and large cases and crates include incline impact tests, described in Test Method D880; horizontal impact tests, described in Test Method D4003.1.2.2 Practice D4169 provides a series of options for selecting and running performance tests on all types of shipping containers and systems.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

Update No. 1 was published as notification that this is now a National Standard of Canada This PDF includes Update No. 1 1 Scope 1.1 General 1.1.1 This Standard specifies minimum requirements for and provides guidance on design principles, sa

定价： 1365元 / 折扣价： 1161 元

1 Scope This technical report outlines principles which are intended to be used as the basis for determining the requirements for connecting large distorting loads (producing harmonics and/or interharmonics) to public power systems. The primary objecti

定价： 1456元 / 折扣价： 1238 元

1 Scope This technical report outlines principles which are intended to be used as the basis for determining the requirements for connecting large fluctuating loads (producing flicker) to public power systems. The primary objective is to provide guidan

定价： 1274元 / 折扣价： 1083 元

5.1 Glass specimens to be tested shall be mounted in a standard test frame with four sides supported, or in a test frame designed to represent specific glazing conditions.5.2 Loads on glass in windows, curtain walls, and doors may vary greatly in magnitude, direction, and duration. Any design load (wind, snow, etc.) that can reasonably be applied to the test specimens or transformed into an equivalent uniform design load can be considered. Load transformation techniques are addressed in the literature (1, 2, 3).35.3 The strength of glass varies with many different factors including surface condition, load duration, geometry, relative humidity, and temperature (4). A thorough understanding of those strength variations is required to interpret results of this test method.1.1 This proof load test method is a procedure to determine, with a 90 % confidence level, if the probability of breakage under design loads for a given population of glass specimens is less than a selected value. It is not intended to be a design standard for determining the load resistance of glass. Practice E1300 shall be used for this purpose.1.2 This test method describes apparatus and procedures to select and apply a proof load to glass specimens, to determine the number of glass specimens to be tested, and to evaluate statistically the probability of breakage. This test method may be conducted using the standard test frame specified herein or a test frame of the user's design.1.3 Proper use of this test method requires a knowledge of the principles of pressure measurement and an understanding of recommended glazing practices.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车