定价： 1840元 / 折扣价： 1638 元 加购物车

定价： 816元 / 折扣价： 727 元 加购物车

定价： 1473元 / 折扣价： 1311 元 加购物车

定价： 2081元 / 折扣价： 1853 元 加购物车

定价： 3204元 / 折扣价： 2852 元 加购物车

定价： 3038元 / 折扣价： 2704 元 加购物车

定价： 541元 / 折扣价： 482 元 加购物车

4.1 GeneralMeasurements and observations described in this document are used to assess the performance of an AM system with a given system set-up and process parameters, in combination with a specific feedstock material.The primary characterization of the AM system obtained by applying this document is via geometric accuracy, surface finish, and minimum feature sizes of the benchmarking test piece(s).4.2 Comparing results from one machineThe test piece(s) can be built and measured for example when the new machine is installed. The test piece(s) can be used to periodically evaluate the performance or diagnose a fault in one AM system, for example, after system maintenance or as specified by the requirements of a quality system.The test piece(s) described in this test method can be used as a demonstration of capabilities for a contract between a buyer and seller of AM parts or AM systems.Data from the measurements described in this document can be used to gauge the impact of new process parameters or material on the AM system performance.Certain test geometries can be included with every build on a particular AM system to help establish performance traceability. Depending on the needs of the user, not all test artefacts need to be built, and individual test artefacts can be built separately if required.1.1 This document covers the general description of benchmarking test piece geometries, i.e. artefacts, along with quantitative and qualitative measurements to be taken on the benchmarking test piece(s) to assess the performance of additive manufacturing (AM) systems.This performance assessment can serve the two following purposes:– AM system capability evaluation;– AM system calibration.The benchmarking test piece(s) is (are) primarily used to quantitatively assess the geometric performance of an AM system. This document describes a suite of test geometries, each designed to investigate one or more specific performance metrics and several example configurations of these geometries into test build(s). It prescribes quantities and qualities of the test geometries to be measured but does not dictate specific measurement methods. Various user applications can require various grades of performance. This document discusses examples of feature configurations, as well as measurement uncertainty requirements, to demonstrate low- and high-grade examination and performance. This document does not discuss a specific procedure or machine settings for manufacturing a test piece.1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 1011元 加购物车

定价： 1114元 加购物车

1.1 The requirements in this document are for part manufacturers using additive manufacturing techniques and are independent of the used material and manufacturing method.1.2 This document specifies criteria for AM relevant processes as well as quality-relevant characteristics and factors along the additive system operations and defines activities and sequences within an additive manufacturing production site.1.3 This document is applicable to the additive manufacturing technologies defined in ISO/ASTM 52900 and defines quality assurance measures along the manufacturing process.1.4 Environment, health and safety aspects are not covered comprehensively in this document. The corresponding content is addressed in the equipment manufacturer guidelines and ISO/ASTM 52931, ISO 27548,2 ISO/ASTM 52933, and ISO/ASTM 52938-1.31.5 This document provides requirements that are additional to those provided by a quality management system (such as, ISO 9001, ISO/TS 22163, ISO 19443, EN 9100, ISO 13485, IATF 16949). Additionally, this document can be used to establish quality management system relevant content that is specific to AM-technology.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 1011元 加购物车

定价： 927元 加购物车

2.1 The terminology included in this standard is intended to provide definitions for sustainable manufacturing terms. This standard is intended to be referenced by other sustainable manufacturing standards.2.2 The terms defined in this standard are those which have specific meaning in the context of sustainable manufacturing. Terms that have more general application, or for which the dictionary definition is applicable, are not included.2.3 Terms having application only within a specific standard, or having meaning unique to the context of that standard, are defined or explained in the terminology section of the individual standard, and are not included here.1.1 The standard includes terminology applicable to sustainable manufacturing.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 515元 加购物车

1.1 This document describes a method for defining requirements and assuring component integrity for plastic parts created using material extrusion based additive manufacturing processes. It relates to the process, equipment and operational parameters. Processes include all material extrusion based additive manufacturing processes. This document is intended for use by AM users and customers procuring such parts. The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system needs to be used independently of the other. Combining values from the two systems can result in non-conformance with this document.

定价： 431元 加购物车

定价： 412元 加购物车