5.1 Identification of a brackish water, seawater, or brine is determined by comparison of the concentrations of their dissolved constituents. The results are used to evaluate the water as a possible pollutant, or as a commercial source of a valuable constituent such as lithium.1.1 This test method covers the determination of soluble lithium, potassium, and sodium ions in brackish water, seawater, and brines by atomic absorption spectrophotometry.21.2 Samples containing from 0.1 to 70 000 mg/L of lithium, potassium, and sodium may be analyzed by this test method.1.3 This test method has been used successfully with artificial brine samples. It is the user's responsibility to ensure the validity of this test method for waters of untested matrices.1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversion to inch-pound units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
定价: 590元 / 折扣价: 502 元 加购物车
4.1 The measurement of soluble oxidizable components of cellulose in sodium hydroxide is indicative of the purity of the cellulose sample, since pure cellulose is insoluble in sodium hydroxide. The extracted components are typically hemicelluloses, which are naturally present in the wood. Differences in pulp purity can have a dramatic impact on the processing and properties of the cellulose derivatives produced from the pulp.1.1 This test method2 is intended for application to dissolving-type cellulose pulps prepared from cotton or wood. The procedure is not directly applicable to unrefined pulps for use in chemical conversion processes because solubility equilibrium may not be attained within the specified extraction time.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
定价: 515元 / 折扣价: 438 元 加购物车
Lubricating greases can contain the lithium soap of hydroxy stearic acid or the sodium soap of various fatty acids as thickeners. The determination of total lithium or total sodium is a measure of the amount of thickener in the grease.1.1 This test method covers determination of the lithium and sodium content of lubricating greases by means of a flame photometer.1.2 A multi-element analysis method for greases, which includes the measurement of lithium and sodium concentrations using inductively couple plasma-atomic emission spectroscopy (ICP-AES), is available in Test Method D 7303.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.The preferred units are mass %.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
3.1 Sodium chloride occurs in nature. It is a necessary article of diet as well as the source for production of many sodium compounds and chlorine. The methods listed in 1.2 provide procedures for analyzing sodium chloride to determine if it is suitable for its intended use.1.1 These test methods cover the chemical analyses usually required for sodium chloride.1.2 The analytical procedures appear in the following sections: SectionSample Preparation 5 to 9Moisture 10 to 17Water Insolubles 18 to 26Calcium and Magnesium 27 to 34Sulfate 35 to 42Reporting of Analyses 43 to 451.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 Review the current safety data sheets (SDS) for detailed information concerning toxicity, first-aid procedures, handling, and safety precautions.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
定价: 590元 / 折扣价: 502 元 加购物车
This guide is recommended for use in analyzing the sodium and potassium content of silver-cadmium oxide materials and is meant to be used in conjunction with standard methods of atomic absorption spectroscopy. The recommended procedures cite methods for minimizing extraneous sodium and potassium contamination through use of specific handling procedures and shorter sample preparation methods. This guide also recommends procedures that prevent the formation of nonstable and potentially hazardous silver-acetylene compounds. 1.1 This guide describes procedures for use in conducting analysis of silver-cadmium oxide materials for sodium and potassium content. The exact methods for the performance of this testing are not stated since many different procedures are equally applicable. This guide points out specific procedures for decreasing the chance of recognized potential errors and specifies methods for increasing the sensitivity of the testing. 1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. For specific precautions see Sections 4 and 6. 1.3 Whoever uses this standard should consult the Material Safety Data Sheet concerning the products involved.