定价： 605元 / 折扣价： 515 元

定价： 0元 / 折扣价： 0 元 加购物车

定价： 481元 / 折扣价： 409 元

定价： 605元 / 折扣价： 515 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

定价： 78元 / 折扣价： 67 元 加购物车

定价： 78元 / 折扣价： 67 元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 156元 / 折扣价： 133 元

5.1 This guide outlines general installation procedures and precautions for the application of sodium bentonite needle-punched geotextile waterproofing systems.5.2 This guide is not all inclusive and is intended only to supplement detailed drawings and specifications from designers and the installation guidelines of manufacturers. Manufacturers of some of the systems addressed by this guide require proprietary products and special procedures not described in this guide. Manufacturers’ guidelines and details applicable for each site construction condition encountered on a project should therefore be considered in the application of this guide.1.1 This guide covers general installation guidelines of waterproofing membranes produced as a composite of sodium bentonite contained within two interlocked needle-punched geotextiles for designers to consider when developing project-specific drawings and specifications. This guide covers construction applications where the waterproofing is applied to the positive side of below-grade cast-in-place concrete foundation walls, both backfilled and support of excavation (SOE) construction, and under concrete pressure slabs. This guide does not cover plaza deck construction applications, either split-slab construction or pavers on pedestals, or vegetated green roof waterproofing applications.1.2 This guide does not cover sodium bentonite waterproofing membranes produced with a corrugation paper carrier, bentonite bonded to a geomembrane, and spray-applied bentonite systems.1.3 For the purpose of this guide, concrete is assumed to be cast-in-place with a surface profile as recommended in Guide D5295/D5295M, consolidated in accordance with applicable guidelines in ACI 309, structurally sound, able to accept the weight of anticipated loads, and meets the local building code requirements. All components of the waterproofing system are assumed to comply with any federal, state, and local environmental regulations that may be in effect at the time of installation. Expansion joints, insulation, and drainage layers are beyond the scope of this guide.1.4 This guide does not cover sodium bentonite geotextile membranes installed on below-grade foundation walls and slabs constructed with masonry materials, precast concrete, or pneumatically applied concrete (that is, shotcrete).1.5 The values stated in SI units are to be regarded as standard. The unit values given in parentheses are for reference information only.1.6 Different sodium bentonite geotextile membranes have different materials of composition and construction which can affect physical properties. The procedures contained in this guide, therefore, may not be universally applicable to all sodium bentonite geotextile membranes under all field conditions.1.7 This guide does not purport to assign responsibilities of quality assurance or quality control. Specific quality assurance and quality control items should be addressed in project specifications and contract documents.1.8 This guide does not purport to include requirements for warranties associated with the waterproofing materials or installation.1.9 This guide does not purport to include all detailing techniques to address various conditions that can be encountered on construction projects.1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

3.1 Soda ash is used in a number of manufacturing processes. The procedures listed in 1.2 are suitable for specification acceptance and manufacturing control of commercial soda ash.1.1 These test methods cover the analyses usually required on commercial soda ash (sodium carbonate).1.2 The analytical procedures appear in the following sections:  Sections Total Alkalinity, Titrimetric  8 – 15Sodium Bicarbonate, Titrimetric 17 – 24Loss on Heating, Gravimetric 26 – 32Moisture, Calculation 34 – 38Sodium Chloride, Titrimetric 40 – 46Sodium Sulfate, Gravimetric 48 – 54Iron, Photometric 56 – 64Sieve Analysis 66 – 721.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.1.5 Review the current Safety Data Sheets (SDS) for detailed information concerning toxicity, first aid procedures, handling and safety precautions.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 6.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车