定价： 260元 / 折扣价： 221 元 加购物车

This specification covers laser-fused stainless steel bars, plates, and shapes of structural quality for use in bolted or welded structural applications. The butt-welded test pieces are welded using laser fusion and then machined into tensile test bars and root-bend test specimens. The term laser fusion is used in this specification to refer to a joining process that is able to produce a coalescence of material using the heat obtained from the application of a concentrated coherent light beam impinging on the surface of a weld joint.1.1 This specification covers laser and laser hybrid welded stainless steel bars, plates, sharp-cornered profile (SCP), and built-up shapes of structural quality for use in bolted or welded structural applications. SCP and built-up shapes are used in, but not limited to, the following applications: industrial and general structural applications like buildings, including architecturally exposed steel structures (AESS); architectural steel profiles, such as curtain wall and staircases.NOTE 1: The term laser fusion is also used to describe laser welding.1.1.1 Supplementary requirements of an optional nature are provided. They shall apply only when specified by the purchaser.NOTE 2: Since the product covered by this specification is manufactured in small lots on dedicated production lines, minimum product quality requirements are ensured by requiring welding process specification and operator qualification at each manufacturing facility in accordance with AWS, ASME, or ISO requirements. If required, the purchaser can specify higher levels of weld inspection; supplementary requirements for mechanical and corrosion testing; and other requirements.NOTE 3: Because of the varying requirements of the end-use applications, different length tolerance and weld inspection levels may be specified.1.2 Shapes covered in this specification include those defined in Article 3.1.2 of Specification A6/A6M, square and rectangular hollow sections, and additional shapes, including customized, that are made from two or more shapes, plates, bar, sheet, or strip.1.3 This specification establishes the minimum requirements for manufacturing of laser and laser hybrid welded stainless steel shapes and requires the welds to, at a minimum, match the tensile and yield strength of the base metal. If base metals of different strengths are used, the lower strength base metal shall be matched.1.4 This specification refers to Specifications A240/A240M, A276/A276M, or A479/A479M for chemical requirements, but the mechanical test requirements are determined by the mechanical properties section of this standard. This standard includes four strength grades. The default strength grade 1 is determined by the base metal standard. Grades 2 through 4 are for specification of higher strength levels.1.5 The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.1.6 Units—This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

4.1 This practice describes to the end user how to collect the FT-IR spectra of in-service oil samples for in-service oil condition monitoring. Various in-service oil condition monitoring parameters, such as oxidation, nitration, soot, water, ethylene glycol, fuel dilution, gasoline dilution, sulfate by-products and phosphate antiwear additives, can be measured by FT-IR spectroscopy (4-7). Changes in the values of these parameters over operating time can then be used to help diagnose the operational condition of various machinery and equipment and to indicate when an oil change should take place. This practice is intended to give a standardized configuration for FT-IR instrumentation and operating parameters employed in in-service oil condition monitoring in order to obtain comparable between-instrument and between-laboratory data.1.1 This practice covers the instrument set-up and operation parameters for using FT-IR spectrometers for in-service oil condition monitoring for both direct trend analysis and differential trend analysis approaches.1.2 This practice describes how to acquire the FT-IR spectrum of an in-service oil sample using a standard transmission cell and establishes maximum allowable spectral noise levels.1.3 Measurement and integrated parameters for individual in-service oil condition monitoring components and parameters are not described in this practice and are described in their respective test methods.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

定价： 975元 / 折扣价： 829 元

4.1 The selection criteria is to be applied for uses of (1) new motors and (2) replacement motors.4.2 For the selection of new or replacement motors, this practice defines the choice criteria in terms of the ordering data below.AbstractThis guide provides the required basic ordering information for low voltage (1000 VAC or less, and up to and including motors of 500 hp) general-purpose (GP), commercial, universal, small and medium sized alternating current electric motors intended to drive common shipboard mechanical machinery such as fans, blowers, centrifugal and screw pumps. This guide does not address the ordering information for special-purpose (SP) motors, definite-purpose motors (for example, cryogenic service), or motors for use in hazardous (classified) locations as defined by the National Electrical Code (NFPA 70). The ordering checklist shall provide the following minimum information: electrical input; speed; power; enclosure; duty cycles; ambient temperature; insulation class; design class; service factor; drive method; mounting arrangement; mounting flange (end shield); rotation; motor conduit box location; closed-coupled; efficiency; and other special requirements.1.1 This guide covers the required basic ordering information for low voltage (1000 VAC or less) general-purpose, commercial, universal, small-, and medium-sized alternating current electric motors for shipboard use, up to and including motors of 500 hp.1.2 The electric motors covered by this guide are general-purpose (GP) motors intended to drive common shipboard mechanical machinery such as fans, blowers, centrifugal and screw pumps.1.3 This guide is not intended to be used to order special-purpose (SP) motors or definite-purpose motors (for example, cryogenic service) or motors for use in hazardous (classified) locations as defined by the National Electrical Code (NFPA 70).1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This practice contains a mechanism to determine that the hazardous constituents have been remediated to an acceptable level.This practice assists both the regulator and the owner/operator in establishing cost-effective steps and procedures necessary to determine if the site has achieved its objective for site closure.This practice can be applied to hazardous and nonhazardous spills or leaks, surface impoundments, waste piles, buildings, and tanks. The general nature of this practice allows its use in a large variety of situations.1.1 This practice covers the steps necessary to determine if a site is ready for closure with emphasis on general sampling techniques and how to determine if the agreed upon level of remediation has been achieved.1.2 A minimum of statistical procedures is used in this practice.1.3 The standard practice does not address radioactive waste sites nor does it cover every situation that can occur in the field. It does cover the following general sampling techniques: soil sampling, swipe sampling of buildings and equipment, surface impoundments, waste piles, and layered tanks. It does not cover drum sampling, general water sampling and monitoring wells and their construction.1.4 The values stated in inch-pound units are to be regarded as standard. the values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices to determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

4.1 This guide provides information and guidelines for the selection of components and the design of a built-up bituminous membrane waterproofing system in building deck construction. Where the state of the art is such that criteria for particular conditions are not established or have numerous variables that require consideration, applicable portions of design considerations, Sections 5 – 16, serve as reference and guidance for selection by the designer of the system.1.1 This guide describes the design of fully adhered built-up bituminous membrane waterproofing systems for plaza deck and promenade construction over occupied spaces of buildings where covered by a separate wearing course.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

This specification covers the standards for the quality and grading of crushed stone, crushed slag, and water-worn gravel intended for use as coarse mineral aggregate on built-up roofs. The crushed stone and gravel shall be hard, durable, opaque, and free of foreign substances. The crushed slag, on the other hand, shall be hard, air-cooled, and free of as well of any foreign particles. The specimens shall comply with the gradation and physical requirements prescribed herein and shall undergo testing which include a gradation test, moisture test, unit mass test, dust, and hardness test.1.1 This specification covers the quality and grading of crushed stone, crushed slag, and water-worn gravel suitable for use as coarse mineral aggregate on built-up roofs.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This test method measures the moisture in mineral aggregate required by Specification D1863/D1863M.1.1 This test method covers the determination of moisture in mineral aggregate for use on built-up roofs.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车