定价： 590元 加购物车

定价： 515元 加购物车

定价： 646元 加购物车

4.1 The 25-mm [1-in.] deflection IFD method is recommended for production screening and quality control on full size cushions only.4.2 Applicable cushion thicknesses to be tested by this test method are only those listed in this test method. Further research and development are required before this test method is applicable to other cushion thicknesses.4.3 This test method is designed to give a value approximating the 25 % IFD on a 100-mm [4-in.] thick piece of foam when the actual specimen thickness tested is within the ranges listed in the test method. In case of disagreement, the referee method is the IFD procedure in Test Methods D3574, Test B1. The user of this test method shall establish the correlation between this test method and the referee method.1.1 This test method covers a screening type quality control test used to determine if flexible polyurethane foam cushions are within the specified grade range for firmness.1.2 This test method is limited to foams with thicknesses that are 75 mm [3 in.] or greater.1.3 This test method is based on the fact that the traditional industry standard thickness for Indentation Force Deflection (IFD) is 100 mm [4 in.], and the traditional percent deflection for IFD acceptance and product planning is 25 %. With respect, then, to these traditional industry conventions, a 25 % deflection on a 100-mm [4-in.] cushion would be 25 mm [1 in.]. Thus, deflecting standard cushions (of proper 100 mm thickness) 25 mm [1 in.] provides a quick way to determine if the flexible polyurethane foam is within the specified grade range for 25 % IFD.1.4 Cushion thicknesses less than 75 mm [3 in.] shall not be tested for IFD using this test method.1.5 This test method is intended to provide a quick and simple method to screen flexible polyurethane foams for determination of its firmness grade.1.6 Units—The values stated in U.S. Customary or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: This test method and ISO 2439 address the same subject matter, but differ in technical content.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

4.1 This specification addresses minimum performance criteria for adhesives used to laminate oriented strand board (OSB) structural panel facing material to expanded or extruded polystyrene core materials. Adhesive performance is based on tests that simulate exposure to moisture, temperature, seasonal weathering, and creep. Additionally, the adhesive is to demonstrate resistance to oxidation, mold, chemical reagents, and compatibility to the specific laminating materials.4.2 The adhesive manufacturers can use this specification for new product development and quality control purposes.4.3 Structural insulated panel manufacturers rely on an adhesive performance specification that determines its suitability before use.4.4 Performance of the SIP adhesive when evaluated in accordance with this specification aids in determining the suitability of the adhesive for laminating OSB facings to rigid cellular polystyrene core materials in the manufacture of structural insulated panels.AbstractThis specification addresses the physical, chemical and test requirements for structural insulated panel (SIP) adhesives suitable for the bonding of oriented strand boards (OSB) to rigid cellular polystyrene thermal insulation core materials for general structural use. Douglas-fir to Douglas-fir assemblies shall pass the following qualification requirements when tested in accordance with referenced ASTM documents enumerated herein: block shear strength (dry shear, soak/re-dry, oxidation resistance, and mold resistance); tensile strength (dry tensile bond strength, soak/re-dry, and mold resistance); and creep resistance. OSB to core to OSB assemblies shall, alternatively, be tested and pass shear strength and tensile (flat wise) bond strength requirements as well.1.1 This specification is designed to evaluate adhesives suitable for the bonding of oriented strand board (OSB) to rigid cellular polystyrene insulation core materials for general structure use.1.2 The requirements of the structural insulated panel (SIP) adhesive are based on the performance of the adhesive as measured by:1.2.1 Resistance to shear by compression loading in ambient conditions and after accelerated aging.1.2.2 Resistance to tensile loading in ambient conditions and after accelerated aging.1.2.3 Resistance to creep (deformation) under static load in ambient conditions and after accelerated aging.1.2.4 Tensile and shear strength to polystyrene core materials.1.3 The classification of the adhesive formulation is based on, but not limited to the adhesive’s industry accepted generic names, for example: phenol-resorcinol, emulsion polymer isocyanate, one and two-part urethane. The type of adhesive application and curing terminology are also usually included for classification purposes such as cold-setting phenol resorcinol, heat-cured phenol resorcinol, and hot melt one component urethane.1.4 Evaluation of adhesive performance at high temperature conditions, such as during a fire exposure, is beyond the scope of this specification.1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

4.1 This practice provides minimum recommendations for preparing and smoothing panel underlayments, thick poured gypsum concrete underlayments, thick poured lightweight cellular concrete underlayments and concrete subfloors with patching compounds. Actual requirements for materials to be used, mixtures, and other details are generally included as part of the project plans or specification details and may vary from the minimum recommendations set forth in this practice.1.1 This practice includes recommendations for preparing and smoothing panel underlayments, gypsum concrete and concrete subfloors with patching compounds upon which resilient flooring may be installed.1.2 This practice does not cover the adequacy of the subfloor assembly to perform its structural requirements, which is governed by local building codes.1.3 This practice does not supersede in any manner the resilient flooring, underlayment or adhesive manufacturer’s written instructions. Consult the individual resilient flooring, underlayment or adhesive manufacturer for specific recommendations.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 515元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车