定价： 110元 / 折扣价： 94 元

定价： 114元 / 折扣价： 97 元

定价： 110元 / 折扣价： 94 元

定价： 114元 / 折扣价： 97 元

1.1 This classification covers acetal materials suitable for molding and extrusion. This specification allows for the use of acetal plastic materials that are recycled, reconstituted, recycled-regrind, recovered, or reprocessed, or combination thereof, provided that the requirements as stated in this specification are met. It is the responsibility of the supplier and the buyer of recycled, reconstituted, recycled-regrind, recovered, or reprocessed acetal plastic materials, or combination thereof, to ensure compliance. (See Guide D5033).1.2 The properties included in this classification are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specialized applications. These may be specified by using the suffixes as given in Section 5.1.3 This classification and subsequent line callout are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the field of plastics design after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification.1.4 The values stated in SI units are to be regarded as the standard.1.5 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1--This classification is similar to ISO 9988-1 and 9988-2, although the technical content is significantly different.Note 2--This classification was revised in 1992 to include international 4-mm specimens and test procedures as the standard for compliance. The 3.2-mm specimens, test methods, and Tables POM, A, and B that were superceded by the revision are included in Appendix X2, as a reference for those wishing to use them. It is recommended that the material manufacturer be consulted on all callouts against this classification.

定价： 0元 / 折扣价： 0 元

This classification covers polyoxymethylene materials suitable for molding and extrusion. This specification allows for the use of polyoxymethylene plastic materials that are recycled, reconstituted, recycled-regrind, recovered, or reprocessed, or combination thereof, provided that the requirements as stated in this specification are met. Test specimens shall be molded by injection molding and all test pieces shall be tested as molded and conditioned in the standard laboratory atmosphere. The mechanical properties of the unreinforced and reinforced, filled, or lubricated polyoxymethylene materials shall be determined and shall conform to the following requirements: flow rate; melting point; tensile strength; tensile modulus; Charpy impact resistance; and deflection temperature.1.1 This classification system covers polyoxymethylene materials suitable for molding and extrusion. This classification system allows for the use of polyoxymethylene plastic materials that are recycled, reconstituted, recycled-regrind, recovered, or reprocessed, or combination thereof, provided that the requirements as stated in this specification are met. It is the responsibility of the supplier and the buyer of recycled, reconstituted, recycled-regrind, recovered, or reprocessed polyoxymethylene plastic materials, or combination thereof, to ensure compliance. (See Guide D7209).1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using suffixes as given in Section 5.1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this standard.1.4 The values stated in SI units are to be regarded as the standard.1.5 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: This classification system is similar to ISO 29988-1/-2, although the technical content is significantly different.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the requirements and test methods for the material, dimensions, workmanship, and properties of extruded, compression molded, and injection molded acetal shapes such as sheet, plate, rod, and tubular bar. The specimens shall be a pure polyoxymethylene or may filled, lubricated, or reinforced with carbon and graphite fiber, glass, PTFE, graphite, silicone, molybdenum disulfide, mineral, combinations of reinforcements or fillers, or both. The products shall conform to the physical property requirements which include tensile strength, elongation at break, tensile modulus, dimensional stability, flexural modulus, Izod impact, and porosity level. Thickness tolerance, length camber, and width bow properties shall also comply with the dimensional requirements of the different acetal shapes.1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded, compression molded and injection molded polyoxymethylene (POM) sheet, plate, rod, and tubular bar shapes, excluding pipe and fittings.1.2 The properties included in this specification are those required for the compositions covered. Section 4 presents a classification system for defining requirements for particular characteristics important to specialized applications.1.3 This specification allows for the use of recycled plastics.1.4 The values stated in inch-pound units are to be regarded as the standard in all property and dimensional tables. For reference purposes, SI units are included in Table S-POM and Table 1 only.1.5 The following precautionary caveat pertains only to the test method portions, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车