微信公众号随时随地查标准

QQ交流1群(已满)

QQ群标准在线咨询2

QQ交流2群

购买标准后,可去我的标准下载或阅读
ASTM D319-04 Standard Specification for Amyl Alcohol (Synthetic) (Withdrawn 2010) Withdrawn, No replacement 发布日期 :  1970-01-01 实施日期 : 

This specification covers synthetic amyl alcohol. The properties of amyl alcohol shall be determined in accordance with the following test methods: apparent specific gravity; color; distillation range; water; and acidity.1.1 This specification covers synthetic amyl alcohol.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.

定价: 0元 / 折扣价: 0

在线阅读 收 藏
ASTM D3540-12 Standard Specification for Primary Amyl Acetate, Synthetic (98 % Grade) (Withdrawn 2021) Withdrawn, No replacement 发布日期 :  1970-01-01 实施日期 : 

This specification covers synthetic primary amyl acetate (98 % grade). The apparent specific gravity, color property, distillation range, water property, acidity, and ester value shall be tested to meet the requirements prescribed.1.1 This specification covers synthetic primary amyl acetate (98 % grade).1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for material listed in this specification.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价: 0元 / 折扣价: 0

在线阅读 收 藏

4.1 This procedure is designed to determine the purity of the two ketones, methyl isoamyl ketone and methyl amyl ketone, and to obtain the concentration of their various impurities, several of which are critical in the application of these solvents.1.1 This test method covers the determination of the purity of methyl amyl ketone and methyl isoamyl ketone. In addition, the method determines total ketones and various impurities which may include acetone, isopropyl alcohol, methyl propyl ketone, methyl isobutyl ketone, methyl butyl ketone, methyl isobutyl carbinol, mesityl oxide, methyl isoamyl ketone, methyl butyl carbinol, methyl amyl ketone, and diisobutyl ketone.1.2 Water and acid cannot be determined by this test method. They must be determined by other appropriate ASTM procedures, and the results used to normalize the chromatographic data.1.3 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded “off to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 For hazard information and guidance, see the supplier’s Safety Data Sheet.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 590元 / 折扣价: 502 加购物车

在线阅读 收 藏

This specification covers methyl amyl acetate2 (95 % grade) for use in paint, varnish, and related products. The apparent specific gravity, color property, distillation range, non-volatile matter, odor property, water property, acidity, and ester value shall be tested to meet the requirements prescribed.1.1 This specification covers methyl amyl acetate2 (95 % grade) for use in paint, varnish, and related products.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 For specific hazard information and guidance, see the supplier’s Material Safety Data Sheet for materials listed in this specification.1.4 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 515元 / 折扣价: 438 加购物车

在线阅读 收 藏
ASTM D1839-14(2019) Standard Test Method for Amyl Nitrate in Diesel Fuels (Withdrawn 2019) Withdrawn, No replacement 发布日期 :  1970-01-01 实施日期 : 

4.1 In diesel fuel, the presence of alkyl nitrates such as amyl nitrate, hexyl nitrate, or octyl nitrate causes a higher residue value than observed in untreated fuel, which can lead to erroneous conclusions as to the coke forming propensity of the fuel. The presence of such alkyl nitrate in the fuel can be determined using this test method. This test method can be used to determine the amount of amyl nitrate that has been added to diesel fuels to improve cetane number. This test method is applicable as a basis for judging compliance with specifications covering amyl nitrate.1.1 This test method covers the determination of 0.1 % to 0.5 % by volume amyl nitrate in diesel fuels.NOTE 1: This test method has been used for the determination of hexyl nitrate in diesel fuels, but has not been cooperatively tested for such samples. For the determination of hexyl nitrate, use standards containing nitrate esters of primary hexanol. Use a density of 0.97 in calculating results.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 0元 / 折扣价: 0

在线阅读 收 藏

5.1 Ethers, alcohols, and other oxygenates can be added to gasoline to increase octane number and to reduce emissions. Type and concentration of various oxygenates are specified and regulated to ensure acceptable commercial gasoline quality. Drivability, vapor pressure, phase separation, exhaust, and evaporative emissions are some of the concerns associated with oxygenated fuels.5.2 This test method is applicable to both quality control in the production of gasoline and for the determination of deliberate or extraneous oxygenate additions or contamination.1.1 This test method covers the determination of ethers and alcohols in gasolines by gas chromatography. Specific compounds determined are methyl tert-butylether (MTBE), ethyl tert-butylether (ETBE), tert-amylmethylether (TAME), diisopropylether (DIPE), methanol, ethanol, isopropanol, n-propanol, isobutanol, tert-butanol, sec-butanol, n-butanol, and tert-pentanol (tert-amylalcohol).1.2 Individual ethers are determined from 0.20 % to 20.0 % by mass. Individual alcohols are determined from 0.20 % to 12.0 % by mass. Equations used to convert to mass percent oxygen and to volume percent of individual compounds are provided. At concentrations <0.20 % by mass, it is possible that hydrocarbons may interfere with several ethers and alcohols. The reporting limit of 0.20 % by mass was tested for gasolines containing a maximum of 10 % by volume olefins. It may be possible that for gasolines containing >10 % by volume olefins, the interference may be >0.20 % by mass. Annex A1 gives a chromatogram showing the interference observed with a gasoline containing 10 % by volume olefins.1.3 This test method includes a relative bias correlation for ethanol in spark-ignition engine fuels for the U.S. EPA regulations reporting based on Practice D6708 accuracy assessment between Test Method D4815 and Test Method D5599 as a possible Test Method D4815 alternative to Test Method D5599. The Practice D6708 derived correlation equation is only applicable for ethanol in fuels in the concentration range from 2.28 % to 14.42 % by mass as measured by Test Method D4815. The applicable Test Method D5599 range for ethanol is from 2.16 % to 14.39 % by mass as reported by Test Method D5599.1.4 Alcohol-based fuels, such as M-85 and E-85, MTBE product, ethanol product, and denatured alcohol, are specifically excluded from this test method. The methanol content of M-85 fuel is considered beyond the operating range of the system.1.5 Benzene, while detected, cannot be quantified using this test method and shall be analyzed by alternate methodology (see Test Method D3606).1.6 The values stated in SI units are to be regarded as standard. Alternate units, in common usage, are also provided to increase clarity and aid the users of this test method.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 646元 / 折扣价: 550 加购物车

在线阅读 收 藏
ASTM D4360-11(2019) Standard Specification for Methyl n-Amyl Ketone Active 发布日期 :  1970-01-01 实施日期 : 

This certification of coating conformance form provides procurement information concerning products being furnished in accordance with a specific coating specification and additional requirements contained in the purchase order. The certification form is divided into four headings: General Type and Description(I), Buyer Information(II), Seller Information (III), and Certification (IV). The first heading consists of the following information: generic type, manufacturer's designation, specification number, formula number, component number, component identification, and color. The second heading consists purchase order number, release number, part number, item number, and stock number. The third heading consists of seller's representative, batch number, lot number, date of manufacture, and date of certification expiration. The last heading is a paragraph describing the certification.1.1 This specification covers methyl n-amyl ketone (98 % grade) for use in paint, varnish, lacquer, and related products.1.2 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.1.3 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 515元 / 折扣价: 438 加购物车

在线阅读 收 藏
7 条记录,每页 10 条,当前第 1 / 1 页 第一页 | 上一页 | 下一页 | 最末页  |     转到第   页