定价： 819元 / 折扣价： 697 元 加购物车

定价： 605元 / 折扣价： 515 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

This specification establishes recognized requirements for determining the child resistance of portable gasoline containers intended for use by consumers. The following tests shall be performed: senior adult test; child-resistant test (test subject/selection criteria); child-resistant tests (test failures); sequential test; and senior adult use effectiveness to conform with the specified requirements.1.1 This specification establishes recognized requirements for determining the child resistance of portable fuel containers (PFCs) and other types of portable containers intended for use by consumers to hold, store, and transport liquid fuels such as gasoline, kerosene, and diesel.1.1.1 “Portable Fuel Container” is defined in Specification F852 and includes the receptacle for gasoline, kerosene, or diesel fuel as well as spouts, caps, and other closure mechanisms and components for use with or on portable gasoline, kerosene, or diesel receptacles.1.1.2 This specification is also applicable to spouts, caps, or other closure mechanisms sold separately for use with or on a fuel container.1.1.3 This specification does not cover one-time use portable emergency fuel containers conforming to Specification F2874.1.2 This standard addresses the effectiveness of the child resistance (CR) device only after closure cycling, but does not address closure effectiveness:1.2.1 When at high or low temperatures,1.2.2 After thermal aging of polymers,1.2.3 After exposure to sunlight,1.2.4 After exposure to intended fuels, and1.2.5 After physical abuses, such as drops or impacts.NOTE 1: Please see Appendix X2 for additional information on these exemptions.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This practice outlines lead hazard reduction methods that have been shown to be effective in preventing lead poisoning in children.4.2 This practice tabulates advantages, disadvantages, and relative costs of the reduction methods to assist professionals such as certified lead-based paint risk assessors, supervisors, or project designers in selecting appropriate cost-effective options for controlling lead hazards identified during a lead risk assessment. Different control methods may be equally effective in controlling a given lead hazard and, consequently, the selection of a specific control method may depend on the needs and economic constraints of the client or building owner.4.3 This practice is intended to complement other lead hazard activities that are performed in accordance with regulations promulgated by authorities having jurisdiction. For example, in some jurisdictions, a lead hazard risk assessment, by regulation, consists of a visual assessment, a hazard assessment including environmental monitoring for lead, and selection of lead hazard reduction methods.4.4 This practice is intended to assist homeowners, owners and occupants of rental property, lenders, insurers, and others who have interest in selecting options for controlling lead hazards associated with leaded paint, dust, or soil.4.5 This practice complements Guide E2115. Information and data gathered in accordance with Guide E2115 and this practice are used in preparing a risk assessment report. Subsequent lead hazards are mitigated through implementation of controls selected in accordance with this present practice.4.6 This practice addresses the most commonly used lead hazard reduction methods. It is left to users of this practice to identify the advantages, disadvantages, and relative costs associated with emerging control technologies for comparison with these characteristics of established lead hazard control methods.4.7 This practice does not address specific historic preservation requirements. The interim control and abatement methods in this practice will work in any structure; however, historic preservation regulations promulgated by authorities having jurisdiction may impose specific interim control or abatement methods.1.1 This practice describes the selection of lead hazard reduction methods for controlling lead hazard risks identified during risk assessments of residential dwellings and child occupied facilities.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.1.3 This practice contains notes, which are explanatory and are not part of the mandatory requirements of this standard.1.4 Methods described in this practice may not meet or be allowed by requirements or regulations established by local authorities having jurisdiction. It is the responsibility of the user of this standard to comply with all such requirements and regulations.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 This test method allows for the measurement of the torque retention properties of container/continuous thread closure systems of various designs, materials, and manufacture, and is suitable for package development and engineering evaluation.5.2 Each test method can be used for the evaluation of non child resistant container/continuous thread closure systems under controlled conditions such as when the application torque is known and the applied downward force to the closure is zero or for Type I, style “A” push down and turn child resistant container/continuous thread closure systems under controlled conditions such as when the application torque and the applied downward force to the closure is known.5.3 This test method measures torque retention properties of container/continuous thread closure systems with the use of an automated transducer based torque meter operating at a known rotational velocity (rpm) or known torque ramp.5.4 This test method is intended for measurement of dry torque only.1.1 These test methods evaluate the torque retention of continuous thread closures on containers with matching finishes, for predetermined environmental conditions over time. Methods are defined for both Type I, style “A” push down and turn Type II2 child resistant and non child resistant type closures.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.NOTE 1: The SI unit system is the recommended system.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This consumer safety specification is intended to address incidents reported by the U.S. Consumer Product Safety Commission (CPSC) relating to frame child carriers. In response to the incident data compiled by the CPSC, this consumer safety specification attempts to minimize the hazards associated with these products from the following: occupant retention, structural integrity, and deficiency of consumer education regarding product use. This consumer safety specification is intended to deal with reasonably foreseeable use and misuse of the products. Performance requirements of the frame child carriers shall be determined by subjecting them to the following tests: leg opening test, dynamic strength test, static load test, stability test, locking device test, unintentional folding test, and removal of protective components test such as torque test and tension test. Instructions shall be provided with the product and shall be easy to read and understand. Instructions for assembly, use, maintenance, and cleaning of the product, and warnings, where applicable, shall be included.1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of frame child carriers.1.2 This consumer safety specification is intended to minimize the risk of injury to a child from the normal use and reasonably foreseeable misuse of these products.1.3 For the purposes of this consumer safety specification, a frame child carrier is a product, normally of sewn fabric construction on a tubular metal or other frame, which is designed to carry a child, in an upright position, on the back of the caregiver. A frame child carrier is intended for use with a child that is able to sit upright unassisted and weighs between 16 lb and 50 lb (7.3 kg and 22.7 kg). The frame child carrier is intended to be worn on the back of the caregiver’s body, with the carrier, and thus the child, suspended from both shoulders of the caregiver. The seated position of the child is either facing towards or away from the caregiver.1.4 No frame child carrier produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with the specification unless it complies with all of the requirements contained herein.1.5 This consumer safety specification is not intended to address incidents and injuries resulting from the interaction of other persons or objects with the caregiver and child while the frame child carrier is in use.1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.7 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1.1 This specification covers safety requirements, test methods, and warnings for child safety locks and latches intended to be installed by consumers to the interior of residential cabinet doors or drawers to restrict access to household cabinets by children under the age of 48 months.1.2 Child safety locks and latches that are not covered under this specification include devices:1.2.1 Installed on the exterior of a cabinet door or drawer,1.2.2 Requiring installation by professionals, or1.2.3 That are an integral part of the cabinet door or drawer system.1.3 This specification does not cover child safety locks, latches, and straps intended for use on furniture or appliances as anchoring devices to prevent tip over.1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This guide is intended to help prevent lead poisoning of children by providing standardized procedures for conducting a lead hazard assessment and providing information needed to develop and recommend lead hazard control options as described in Practice E2252.5.2 This guide is applicable for use in either occupied or unoccupied dwellings and in other child-occupied facilities.5.3 The procedures in this guide, when supplemented by recommendations for controlling lead hazards, provide for the conduct of a lead risk assessment of a dwelling or of other child-occupied facilities.5.4 This guide may be used to supplement assessment procedures used to determine the causes of elevated blood lead (EBL) levels in young children.NOTE 2: In cases of EBL levels, investigation of the total living environment of the child and a pediatric medical evaluation may also be needed. Reference should be made to documents such as Managing Elevated Blood Lead Levels Among Young Children,6 Preventing Lead Poisoning in Young Children (1991),7 the HUD Guidelines, and Screening Young Children for Lead Poisoning (1997).75.5 Although this guide was developed for dwellings and for other child-occupied facilities, this guide may be suitable for lead hazard assessments in non-residential buildings and other properties following agreement between assessor and client on appropriate lead action levels.5.6 This guide is not intended for use in identifying building materials that when abraded or otherwise degraded, such as that which may occur in remodeling or renovation activities, may result in lead hazards.5.7 Lead hazard assessment reports describe lead hazards identified at the time the assessment was performed. The locations, types, or severities of lead hazards can change over time as a result of property improvement or deterioration, significant changes in property use, or other factors.NOTE 3: The term “lead-free” should never be used to describe the absence of lead hazards because testing methodologies are not designed to measure the total absence of lead. Small amounts of lead present in building materials and components or soil may result in a hazard with changes in building conditions or as a result of activities that create dust that contains lead.5.8 This guide is applicable for assisting professionals, homeowners, owners or occupants of rental property, lenders, insurers, and others with a property interest in determining the presence of lead hazards.5.9 This guide also is applicable for assisting designers of lead hazard mitigation projects to target resources toward lead hazard controls that are deemed most likely to result in the prevention of lead poisoning in young children.1.1 This guide covers how to conduct, document, and report findings of a lead hazard assessment of dwellings and of other child-occupied facilities.1.2 Procedures for assessment of personal items, such as toys, dishes, and hobby materials that may contribute to elevated lead levels in blood are not included in this guide.1.3 Procedures for random sampling of units within dwellings having multiple units are not included.1.4 This guide contains notes, which are explanatory, and are not part of the mandatory requirements of this guide.1.5 The values stated in SI units are to be regarded as the standard.1.5.1 Exception—The inch-pound and SI units shown for wipe sampling data are to be individually regarded as standard for wipe sampling data.1.6 Methods described in this guide may not meet or be allowed by requirements or regulations established by local authorities having jurisdiction. It is the responsibility of the user of this standard to comply with all such requirements and regulations.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification covers child carriers that position the child ahead of the rider and behind the handlebar of a bicycle. These child carriers transport children with a minimum weight of 12 kg and a maximum weight of 27 kg who are capable of sitting unaided.1.2 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This standard includes Update No. 2. 1. Scope 1.1 General This Standard applies to nonreclosable packages for drugs and any other substances, in either liquid or solid form, that incorporate child-resistant features whereby children are restricted

定价： 364元 / 折扣价： 310 元